Desert Turtle Racing KOH 2018 Race Recap

Desert Turtle Racing KOH 2018 Race Recap

KOH 2018 Race Week:
First and foremost, we were stoked to be setting up our pits in the Lasernut Laser Town hanger. We arrived at Laser Town and got the Turtle set up in the hanger and set up all our camp stuff. We did a little last minute shock tuning on the Rock Krawler shocks to get them dialed in for race day, then headed over to get registered for the race. Monday was our qualifying day and in practice we discovered that the motor was running not so peppy. We learned that we had to shift to 4-Lo just to get up the hill climb and then shift back into 4-Hi to finish the lap. It hurt our qualifying times a bit but we were still able to get an 11th in class start for Thursday’s race. We also discovered that we had a melted coil pack and spark plug that were causing the engine to run poorly. We were able to get in a run around Lap 1 of the KOH course and mark down some trouble spots on GPS as well as set up our lines to get through the new “Notches” area that Ultra4 added to the course this year. We were feeling pretty good about the course of Lap 1 and the car was running well. We headed out for a pre-run of Lap 2 and got through a couple trails but unfortunately cracked the oil pan on a couple big hits and that caused us to call the pre-running extremely short. A big part of our pit support this year was provided by Dust Junkies Racing and they just so happened to be near where we broke down and gave us a helping hand to get back to Laser Town. We spent the rest of our pre-running time hunting down an oil pan and making repairs to the rig and studying the course map.

27710053_1755292927854462_1643465511548694151_o

KOH 2018 EMC Race Day:
Let’s just start with, the green flag dropped and we were off and running! Darin was behind the wheel and ready to attack the desert lap. The first few miles had us on edge, knowing that race nerves can cause you to overdrive the rig and/or potentially suffer flats. As we clicked off the early miles we passed many rigs that had suffered exactly that, and a couple others with some quick driving decisions. We were able to maintain a good pace and cruise through unscathed. As we passed by RM12 we felt the rig was doing well. We radioed to Dust Junkies at Remote Pit 1 that we didn’t need a tire change and opted pass through without a stop. They responded with “Well done. We’ll catch you on the flip side at RM48”. We waved on the way by the pits and were feeling great about the rig. We kept clicking off the miles, passing other racers along the way. As we arrived at “The Notches” a little ways past RM24 we followed a couple other rigs into the banner area. Again, we passed a few others that were floundering in the rocks not knowing where to go. We stuck to our pre-planned route and managed to maneuver around a couple more. As we exited, we were on the tail of a 4800 rig and we decided to go for the pass in a whooped-out section to the drivers left. We made the pass, but we also went for a good ride when the front end got bucked pretty high, and we were reminded that we needed to tone it back.

 

We got back on our pace as we rounded the half-way point at RM32, and we continued carrying a good pace, picking our way through the tight desert section before reaching RM47, where we again needed to radio to the Dust Junkies at Remote Pit 1 what our plans were. We chatted for a bit about how the rig was doing, we were not hearing any strange sounds, and we again didn’t need to stop for a tire change. We hit the pit zone and again gave the big thumbs up as we passed by. Heading out crossing the base line we knew the speeds were going to pick up as we rounded the big bend at RM52. Around RM54 we had a close encounter with a bird — this bird was about 20 feet off the deck and clocking us for speed about 50 feet off the front passenger corner of the rig. At least it seemed that close. So we mashed the gas to pick up the pace and see what they would do. We gave them the applause and enjoyed the camera man hanging off the side of the helicopter. Let’s hope it makes the cut into some footage somewhere.

27913184_10156232489085337_146544314158887930_o

We reached the intersection at the baseline exit and headed out across the dry, dusty Melville lakebed. At times we couldn’t see much more than a few feet in front of us. Picking our way up into the top of Resolution, preparing for our drop down it and Backdoor, we knew we had just a couple more miles before we were back to Main. We had a bit of a close call at Backdoor — we got in a little bit of a hurry to prevent another rig from passing us and did a great nose pose with the rear tires straight up in the air. We hit the gas to prevent the roll-over and hit the rear bumper hard on the rock wall behind us… BUT we were down and all four wheels and the rig was still moving. We called in to pits that we were down but took a hard hit and would need to look the rig over really well. We made the last of the little climbs before hitting the short course and the Main Pits. At this point we were pretty stoked Darin just had a VERY clean run on Lap 1 and suffered ZERO flats with our Falken tires. We had a feeling that we were sitting in a pretty good position and it was time to change drivers.

And so the race continues… Lap 2 — Randall is now in the driver’s seat and ready to take on the rock sections. Before we got there, we had to run through the first 8 miles of the Lap 1 again, and then around the desert for another 9 miles before reaching Remote Pit 2A. Again, we kept a descent pace intent on not overdriving the rig. As we reached Remote Pit 2A the rig was feeling pretty good and we called in to let them know that we would just be passing by. We headed into the first rock trail, Boulder Dash, and made pretty quick work of it. We headed down Upper Big Johnson and continued across the valley and around to the bottom of Wrecking Ball. While we were in Wrecking Ball we had a few difficulties leading up to the waterfall but cruised right up the bypass line and continued on. At RM85 we headed over to Fissure Mountain to run across the top of the range and down to Sledgehammer. Another new thing for the Ultra4 race this year was the addition of two trails at RM90, Idle Issues and Her Problem, two trails that I did not get to pre-run nor even see. As we approached the trail we saw the trail markers but the terrain looked untraveled and there were no obvious lines. There was no stopping us on this trail we picked it apart, as if we were cutting a new trail. We had a little trouble getting through Chocolate Thunder but were able to keep our cool and get back on track.

IMG_4236 copy

Once we got over into Jack North we felt something strange in the steering and decided we should stop and take a look. What we discovered was the mount on the axle for the Hydro Assist Ram has been torn off and the Ram was just hanging there cycling left and right. We also discovered that all of the drive flange bolts on the rear axle (BOTH SIDES!) had backed out and we were leaking a ton of gear oil. We tightened up the flange bolts, removed the hydro-ram and capped the hydro lines so we could continue the race. We wheeled up to the crux of Jack North and, like a replay of last year, Darin got out and spotted the rigs through and then got us through and we headed for Jack Hammer. The problem with not having Hydro Assist is that every rock the tires come in contact with will jolt the tires one way or another and that makes it very difficult to steer and stay on the line that you need to get over the rocks. Coming down Jack Hammer we made sure to plan way ahead and keep the car on the right line. Heading up the sand hills at RM93 was pretty fun with the new motor screaming as we made our way. We got around to Hells Gate and continued to struggle with the ability to steer and stay on the right line. Thankfully we had a new ZEON 10 winch from Warn on the rig to get us quickly un-stuck when necessary.

We cruised down Devils Slide and headed over into Sunbonnet Pass. We came upon a few other rigs in the trail and made passes when we could but also got stuck a few times, and again had to use the winch to get unstuck. Somewhere in Sunbonnet we got lodged between two big rocks and had to use our jack to get out, which cost us a significant amount of time. At that point we also discovered that we had cracked the oil pan again and it is was dripping. We took some time to look at the leak and see if we could spot the crack. We debated continuing the race with the leak but the concern was, if we cracked the oil pan even worse, we could damage the motor and possibly be stuck in a trail until the race is over. We agreed that we would make our way out of Sunbonnet and then reassess the condition of the rig. It’s always a hard decision to make but we had to make it. We decided to make our way to the stock bypass split at RM100 and call the race. We didn’t want to risk severe damage to the motor and didn’t want a late-night team recovery after the race. We got in touch with our pit crew at Remote Pit 2B and had them relay to Race Ops that we were out of the race at RM100.

Conclusion:
We finished our race as the 1st place DNF, putting us officially in 4th place by progression. Yes, you read that right — There were only three 4500 class rigs that finished the race, and only another nine rigs in the 4800 class. This race was a difficult one — Not because of the number of rock trails or a difficult desert lap, but because Mother Nature has not rained on the Hammer trails in some time, and that caused the dirt to be very dusty and the rocks to be covered in dust, and some holes to be extra deep.

28070597_1821763607853946_103737264997051737_o

We would like to give a special thanks to several sponsors – To Off Road Development for providing the shop space for us to get ready for KOH. To Sucuri Security for stepping on board to support the team this year. To Warn for going above and beyond standard customer service to solve our winching issues. To Dust Junkies Racing for providing pit space and pit support at the race. To Lasernut for providing us space in the Laser Town Hanger at KOH. To Rock Krawler for their continued support in our race program. To Falken for providing ZERO flats this year on the Wildpeak M/T tires. And to our DTR team… Without them we would not be able to do what we do. We are a team that is more like a family and we are all in it together. Even though we did not finish, we did not lose. We come away smarter and stronger. We are still a young team and we continue to learn at every race.

Thanks to all of our sponsors for your continued support: Rock Krawler Suspension | Falken Tire | Sucuri Security | Axial Racing | Poison Spyder Customs | Raceline Wheels | DJ Safety | Fuel Safe | Rugged Radios | J. E. Reel | Rugged Routes | Lasernut | Currie Enterprises | Magnaflow | CTM Racing | sPOD | Artec Industries | PRP Seats | Luxwurx | Warn | Sharq Skinz | DGP Motion Media | Factor55 | 212 Performance Gloves | Off Road Development | Pacific Advisors | SoCal Services | Beachview Insurance | Villa Landscape Products | SoCal Land Maintenance | EctoVentures

IMG_4222 copy IMG_5348 copy

Building the full size SCX10XJ: Part 1

tech_scx10xj

Words: Scott G

When setting out to build a trail worthy rig, so many things go through your mind. What do you expect from the rig? What do you plan to do with it? What budget do you have to work with? These are all extremely important things to consider when selecting the donor vehicle. However, just know that no matter what you plan for, there will be extras needed, to include the expectations, plans, and budget. Building a 4×4 vehicle to go deep into the elements is not an easy task, and like most things in life, you get what you pay for. This means you have to outfit your choice with the best components available within your budget that will allow you to attain your goals.

This is not at all unlike developing the new SCX10, as all of the same parameters are considered, to include performance expectations and budget restraints. Not budget restraints for development, but budget restraints of our fans and customers. We often read the forums and see what people would like to see in the Axial vehicles. We are forced to make some difficult decisions when finalizing the package, as we want to include the world with these rigs, but also don’t want to ask for $699 for an RTR to get in the game. It is like that with all Axial products, so we do our best to aim for the sweet spot, enough features to perform at the top level, with a reasonable price tag. This is not an easy task. We are faced with the same decisions when building a full size rig. Do we want a supercharged V8, 1000 minimum on the RTI ramp, seating for 4, bulletproof axles? Of course we do, but the budget doesn’t allow for all of them, so we settle for what we can and have a blast doing it.

One of the most common things we read is…. “Oh no, not another Jeep vehicle”, well, I am here to tell you that most of us are Jeep people, so get over it. The Jeep brand is synonymous with the art of back country exploration with extreme reliability, exactly what we strive for with our little brand. It is a perfect marriage and we are happy.

When looking into new options for the new SCX10, we did what all outdoor enthusiasts do, we went into the woods to think about it, to do a little research. We were checking out all the rigs out on the trail and noticed that the XJ was a very popular rig for the most hardcore wheeler and for family back road exploration. We saw XJ’s that were exo-caged on 40′s all the way to bone stock 4×4′s loaded with the whole family and dog. This platform was exactly what we were looking for. It is one of the most popular 4×4 vehicles ever built, with millions of them on the road. Some say that Jeep actually invented the SUV with this release. It was not adapted right away for off-road use, as the old guard (Read: Wrangler, CJ5 and CJ7 owners) looked down upon these Jeeps, calling them cars with big tires, and promptly showing their owners the direction toward the nearest shopping mall or soccer field.

Some XJ inspiration we found on YouTube…

I personally had this experience with my 1993 Jeep grand Cherokee, I was given directions to the soccer field, immediately preceding my climbing an extremely nasty Granite rock face on Los Coyotes Indian reservation back in 1996. The CJ owners immediately began to bicker and argue that the other should climb it. Neither one did, nor did they express themselves again to me on the trail. They learned that day that a Unitized chassis wasn’t the end of the world, and that coil springs are like magic. The Cherokee (XJ) shared the same front suspension with the ZJ, though the XJ had leaf springs in the back, something the Jeep guys were used to back then. Any of the XJ’s and ZJ’s on the trail were hand built, as there were very few aftermarket components available with the exception of suspension which was primarily available to fit larger tires. We told some of our JK friends about our XJ desires and they immediately started flowing some memes our way, most of which we cant publish, but here are a few gems that made us laugh…

xjs

Thanks for the support guys…sheesh.

Fast forward 20 years, and these old grocery getters, mall crawlers or soccer field shuttlers are now extremely common to find on the trail. The off-road community has more than accepted them and many aftermarket companies now make a decent living supporting them. The hard part, finding a clean one-owner version with no rust and low miles, kind of like finding a Unicorn. One of Axial’s more predominant partners, Currie Enterprises, was at the forefront of developing suspension for these rigs so that they could be raced in a desert series called Jeep Speed back in the day. We consulted the Currie family and were introduced to Matt Chapman, the owner of the Cherokee that we based our SCX10XJ off of. As we have done in the past, we like to build the full size version of our scale rigs (see here…) to go out and experience what they can do, and stay on the forefront with regards to what the community is doing. At this time, Matt’s Cherokee was bone stock, as it had just been purchased and not modified yet. We elected to team with Matt and the Currie’s in effort to help develop the Full size XJ into an awesome trail machine all the while developing and testing our SCX10 II in tandem.

Here is a shot of Matt’s XJ when he got it, no rust with 150K miles…

After a good amount of research, we started to compile a list of necessities. We knew the rig had to be able to go with 4 door JK’s on 37′s, as most of Matt’s friends were rolling newer JK’s. We needed at least 35″ tires. Fitting 35′s under the Cherokee would require some proper fender flares and keeps the cops in Moab at bay. Notch Customs said “35″ tires with a 4″ lift, some welding required”. Currie makes a great suspension system for the XJ as well as their bulletproof Rock Jock 44 axles, and you know we love the performance of Icon Shocks. So, what we really needed was some armor. We looked long and hard at so many companies making XJ parts, and there is some awesome stuff out there. Russ at Notch Customs introduced us to JCR Off-Road, who ended up having one of the most complete armor systems available. Then we needed some lighting, the natural choice was Rigid powered by sPOD. Almost forgot wheels and tires. In effort to make the full size version look more like the RC, we elected to run a 35X12.50X17 BFG KO2 All Terrain wrapped around Method Mesh wheels. The 17″ wheel looks closer to a 1.9 than a 15″ wheel. Of course we needed some nice tone out of the 4.0 straight 6, so the XJ would need a Magnaflow exhaust. We had some details to sort but the main wish list was assembled!

First things first, the rig had to be made as reliable as possible by going through everything mechanical. We changed all the fluids, belts, hoses, pretty much everything we could to ensure reliability.

So, building a full size rig is just like building a scaler, get the base kit, then select all the options you wish to install. Here is our list!

2000 Jeep Cherokee XJ Parts list:
Currie Rock Jock 44 front high pinion axle with 4:56 gears
Currie Rock Jock 44 rear axle with 4:56 gears
Currie Rock Jock 4.5″ suspension system
Currie Antirock Sway bar system
EATON E-Locker rear, Detroit Locker front
JCR Vanguard Front winch bumper – No stinger
JCR Rear Bumper – tire carrier ready
JCR XJ Classic sliders
JCR Transfer case skid plate
JCR Gas tank skid plate
JCR Adventure roof rack
Notch Customs fender flares
Rigid 50″ E-Series LED bar
Rigid Dually x2 (front and rear bumper)
PSC Ram assist kit – steering
ICON Vehicle Dynamics 2.0 Aluminum shocks
Magnaflow exhaust
sPOD – Source with Bluetooth control
17X9 Method Wheels – Mesh (5)
35X12.50X17 BFGoodrick KO2 All Terrain tires (5)

Before we started the build process, Jamie Seymour, Axial’s R&D Industrial Designer and resident rendering expert whipped up this drawing for us to envision the build…

Stay tuned as we add more of this story in the coming weeks……

Axial – The Official R/C vehicles of Ultra4 Racing – King of the Hammers 2016

news_koh2016

FOR IMMEDIATE RELEASE:
(Mission Viejo, CA) January 11, 2016.

Axial R/C Inc., A subsidiary of Hobbico Inc., is proud to announce Axial as the Official R/C Vehicles of Ultra4 / King of the Hammers for 2016.

Ultra4 Racing is the latest and greatest off road motorsport event on earth. This style of racing challenges man to a duel with the elements. Unlike standard off road racing in a stadium or in the wide open desert, Ultra4 vehicles face challenges that no other motorsport demands. Competitors are not only made to cross vast areas of open desert, they also travel up boulder strewn canyons and negotiate terrain that appears impassable. To compete in such a demanding environment, competitors build custom four wheel drive vehicles that are made to crawl over the harshest terrain, then conquer the wide open desert at exhilarating triple digit speeds. This element of automotive enthusiasm is precisely what Axial R/C has set out to deliver in 1:10 scale, so the relationship between Axial R/C and Ultra4 is a very natural fit.

Axial’s roots are directly tied to motorsports, especially competitive rock crawling. As full size competitive rock crawling transcended into what is now rock racing, the sport became globally recognized in a short five years, most notably the King of the Hammers [KOH] held annually in Johnson Valley, California. Axial followed suit with its own version of vehicles that translated well within this segment of the off road community. Axial has been very off-road lifestyle driven and fits perfectly with Ultra4 and the King of the Hammers event which is the mecca of enthusiasts pushing the boundaries of rock racing. Axial will be on site at the 2016 King of the Hammers offering enthusiasts an opportunity to experience the endless fun that these rock racing and trail navigating R/Cs have to offer.

Come out and join us at the 2016 King of the Hammers in the Axial compound located smack dab in the middle of Hammertown, USA. This year’s compound will feature a rock racing track and a scale trail where you can traverse a challenging course with your SCX10 vehicles and rip around the track with your Yeti, Wraith or RR10 Bomber. The scale trail will be open for runs during the day, then be closed down for some rock racing in the evenings.

Axial to support drivers chasing the Crown
In 2016, the Axial team will be supporting, following, and cheering on several teams competing in events all week long. Please show these teams some love!

Randy Slawson – Bomber Fab
Casey Currie
Savvy Motorsports
Desert Turtle Racing
Poison Spyder Motorsports
Cody Waggoner – LaserNut
Tom Wayes

The schedule for Axial events is as follows:

Axial Booth open daily Tuesday through Friday 9 AM until Race completion nightly

Tuesday February 2nd, 2016
11-1 Scale Adventure
1:30-2:30 Scale Adventure
3-5 Track open Practice
6PM Outlaw KOH Race for points

Wednesday February 3rd, 2016
11-1 Scale Adventure
1:30-2:30 Scale Adventure
3-5 Track open Practice
6PM Outlaw KOH Race for points

Thursday February 4th, 2016
11-1 Scale Adventure
1:30-2:30 Scale Adventure
3-5 Track open Practice
6PM Outlaw KOH Race for points
Awards immediately following Final Race.

Friday Feb 5th, 2016
Race Day – Get out in the desert and watch the full size racers go for broke chasing the coveted crown and title of “King of the Hammers” for 2016

Outlaw Classes Rules:
1.9 Axial Based Chassis (Except Yeti)
2.2 Axial Based Chassis (Except Yeti)
Yeti Trophy Trucks
Yeti Class (No XL)

Demo Rules:
One try per day – per person
Under 18 – Parent MUST be present.
If you have your own rig, Scale rules apply, Respect the Course!!

**Important Note for 2016**  
There will NOT be a G6 event on Saturday at this year’s King of the Hammers.

About Axial
Founded in 2005, Axial R/C, Inc. has quickly became a global brand leader of hobby grade radio controlled products as Axial is a company of enthusiasts for enthusiasts. We manufacture chassis and accessory products predominantly for the Rock Crawling and Overland Adventure segments, with design emphasis on rugged construction and scale realism. Axial is regularly involved in local and national events which allow us to keep our finger on the pulse of R/C culture, thus earning us awards every year from 2007 through 2010, including “Best Truck”, “Most Innovative”, “Best Engineered Product of the Year”, and “People’s Choice.”

For more information on Axial and Axial products please visit www.axialracing.comtwitter.com/axialracingfacebook.com/axialincyoutube.com/axialvideos

About Ultra4
Ultra4 Racing is the official website of Hammerking Productions. The founders of Hammerking are the force behind the toughest one-day off-road race on the planet: King of The Hammers. King of the Hammers takes place each year in February, on public lands in Johnson Valley, CA. The race has evolved from 12 teams racing for bragging rights and a case of beer, to more than 150 teams competing before thousands of fans both live and online. Due to the incredible success of King of the Hammers, Hammerking has created an equally difficult off-road endurance race called The Stampede which occurs annually in Reno, NV.

In addition to these races, Hammerking has established a racing class known as the Ultra4 class. The defining characteristic of this class is that all cars must be capable of 4-wheel drive. Beyond that, the class is unlimited, which means these cars come in all shapes and sizes and are capable of speeds over 100+ MPH and still contain gear ratios as low as 100 to 1 for technical rock crawling.

To give these cars and their drivers a chance to showcase their unique capabilities, Hammerking has formed the Ultra4 Racing series. The series challenges drivers to compete in a wide variety of terrain from endurance desert racing to competition-style rock crawls to short course racing. Hammerking currently produces five of the six races in the series on their own. The races take place on both public lands and in private motorsports parks across the country including: Exit 28 Motorsports Park in Nevada, Rausch Creek in Pennsylvania and Miller Motorsports Park in Utah.

If you would like to know more about Hammerking, Ultra4, the races produced and/or the movies created, please visit www.ultra4racing.comtwitter.com/Ultra4racingfacebook.com/Ultra4Racingyoutube.com/HeavyMetalConcepts

 

Axial – The Official R/C vehicles of Ultra4 Racing – King of the Hammers 2015

blog_axialg6koh

FOR IMMEDIATE RELEASE:
(Mission Viejo, CA) January 14, 2015.

Axial R/C Inc., A subsidiary of Hobbico Inc., is proud to announce Axial as the Official R/C Vehicles of Ultra4 / King of the Hammers for 2015.

Ultra4 Racing is the latest and greatest off road motorsport event on earth. This style of racing challenges man to a duel with the elements. Unlike standard off road racing in a stadium or in the wide open desert, Ultra4 vehicles face challenges that no other motorsport demands. Competitors are not only made to cross vast areas of open desert, they also travel up boulder strewn canyons and negotiate terrain that appears impassable. To compete in such a demanding environment, competitors build custom four wheel drive vehicles that are made to crawl over the harshest terrain, then conquer the wide open desert at exhilarating triple digit speeds. This element of automotive enthusiasm is precisely what Axial R/C has set out to deliver in 1:10 scale, so the relationship between Axial R/C and Ultra4 is a very natural fit.

Axial’s roots are directly tied to motorsports, especially competitive rock crawling. As full size competitive rock crawling transcended into what is now rock racing, the sport became globally recognized in a short five years, most notably the King of the Hammers [KOH] held annually in Johnson Valley, California. Axial followed suit with its own version of vehicles that translated well within this segment of the off road community. Axial has been very offroad lifestyle driven and fits perfectly with Ultra4 and the King of the Hammers event which is the mecca of enthusiasts pushing the boundaries of rock racing. Axial will be on site at the 2015 King of the Hammers offering enthusiasts an opportunity to experience the endless fun that these rock racing and trail navigating R/Cs have to offer.

On the Saturday following KOH [Feb 7th], there will be a radio controlled version of King of the Hammers as Axial hosts the RECON Ultra4 G6 at King of the Hammers.

blog_recong6koh

Axial RECON Ultra4 G6 at King of the Hammers
When: Feb. 7 – 12:00 Noon
Where: (GPS- N34 24.927, W116 31.090) just west of Hammer Town at the base of the mountain.

R/C motorsports joins full size motorsports once again as Axial joins forces with Ultra4 / King of the Hammers. 2015 will once again see Axial bring the RECON G6 Series along for the full experience. Axial has teamed with full size motorsports in the past and is doing it again in Johnson Valley, Ca. ,on Saturday Feb. 7th, the day after the King of the Hammers main event. This is the last event on the 2015 KOH schedule starting at noon on Saturday, if you own an Axial R/C, come out and get your fix in this historic RECON Ultra4 G6. The RECON G6 series is made up of R/C endurance events featuring man and scale machine tackling the elements, a true test for your R/C vehicle with a major emphasis on a family fun atmosphere. The object is to conquer the course set forth by RECON G6 mastermind Brian Parker. For more information on this event, and to register to participate, please click here.

About Axial
Founded in 2005, Axial R/C, Inc. has quickly became a global brand leader of hobby grade radio controlled products as Axial is a company of enthusiasts for enthusiasts. We manufacture chassis and accessory products predominantly for the Rock Crawling and Overland Adventure segments, with design emphasis on rugged construction and scale realism. Axial is regularly involved in local and national events which allow us to keep our finger on the pulse of R/C culture, thus earning us awards every year from 2007 through 2010, including “Best Truck”, “Most Innovative”, “Best Engineered Product of the Year”, and “People’s Choice.” For more information on Axial and Axial products please visit www.axialracing.comtwitter.com/axialracingfacebook.com/axialincyoutube.com/axialvideos

About Ultra4
Ultra4 Racing is the official website of Hammerking Productions. The founders of Hammerking are the force behind the toughest one-day off-road race on the planet: King of The Hammers. King of the Hammers takes place each year in February, on public lands in Johnson Valley, CA. The race has evolved from 12 teams racing for bragging rights and a case of beer, to more than 150 teams competing before thousands of fans both live and online. Due to the incredible success of King of the Hammers, Hammerking has created an equally difficult off-road endurance race called The Stampede which occurs annually in Reno, NV.

In addition to these races, Hammerking has established a racing class known as the Ultra4 class. The defining characteristic of this class is that all cars must be capable of 4-wheel drive. Beyond that, the class is unlimited, which means these cars come in all shapes and sizes and are capable of speeds over 100+ MPH and still contain gear ratios as low as 100 to 1 for technical rock crawling.

To give these cars and their drivers a chance to showcase their unique capabilities, Hammerking has formed the Ultra4 Racing series. The series challenges drivers to compete in a wide variety of terrain from endurance desert racing to competition-style rock crawls to short course racing. Hammerking currently produces five of the six races in the series on their own. The races take place on both public lands and in private motorsports parks across the country including: Exit 28 Motorsports Park in Nevada, Rausch Creek in Pennsylvania and Miller Motorsports Park in Utah.

Hammerking Productions has also produced three full-length feature films chronicling the first three King of the Hammers races. These award winning movies have helped shine a spotlight on this new form of racing throughout the world. Currently, fans are eagerly awaiting the release of Hammerking’s fourth production which will be coming to theaters and DVD by mid 2011.

If you would like to know more about Hammerking, Ultra4, the races produced and/or the movies created, please visit www.ultra4racing.comtwitter.com/Ultra4racingfacebook.com/Ultra4Racingyoutube.com/HeavyMetalConcepts

###

Jeeping with Casey Currie at EJS2014

blog_jeepingcasey

Casey Currie is an absolute Jeep fanatic. Anyone who follows Casey can see this plain as day, though until you spend a few days with him, you can’t truly know how bad he has it. All hours of the night, in the worst weather conditions, regardless of what is going on or what time it is, Casey is ready to go wheeling. At this years’ EJS, we jumped in the Axial grocery getter, soccer mom mall crawler, whatever you want to call it, and headed out to meet with Casey. He said he had both of his JKs and he was ready to have some Moab fun.

DSC_0022

DSC_0036

DSC_0038

Upon arrival, we see that Casey wasted no time modifying both of his Jeeps. His full size rig was all decked out. We also noticed his Scale JK was equipped with Vanquish Currie Rock Jock axles, Vanquish Rigid Industries light bar, Vanquish front dig, RC4WD Warn Winch. He chose the 55t Axial motor running on 3s for smooth crawling. Once we arrived on Hell’s revenge, he immediately jumped out of his full size JK and started attacking the rock with his SCX10.

DSC_0074

Casey always immediately goes for the “Man’s Line”

DSC_0062

DSC_0067

We just had to get some video to share with you, check it out!

Axial R/C to support Inaugural Silver State 4wd & UTV Jamboree

blog_silverstate

FOR IMMEDIATE RELEASE:
Axial R/C to support Inaugural Silver State 4wd & UTV Jamboree

Axial R/C Inc., A subsidiary of Hobbico Inc., is proud to announce a marketing partnership with Carrera Performance Group LLc. The Axial R/C team will be headed to Reno, Nevada for the week of July 14th through July 18th attending the inaugural Silver State 4wd & UTV Jamboree for a week full of adventure!
The Silver State 4wd & UTV Jamboree (SSJambo) is a first year event catering to everything adventure and off road. Located in Northern Nevada, this event is packed full of reasons to spend a week exploring and enjoying the outdoors with friends.

The week kicks off on Monday July 14th with an Off Road Business Association (ORBA) OHV leadership summit. This is where some of the most influential minds get together to shape the future of the off highway community. This is also one of the most active groups fighting to keep public lands open for off highway recreation.

Tuesday July 15th starts with the Genright Tour to Virginia city for sightseeing to include the Comstock, the first major Silver Ore discovery in the United states. The day will end with the RallyVenture welcome party.

Wednesday July 16th marks the start of the RallyVenture. The RallyVenture is just like a RECON G6 for full size rigs. Axial is one of the 25 teams invited to participate in this invite only inaugural event. The full size SCX10JK will be piloted by Axial staff as they attempt to make history in Nevada!

Thursday July 17th will have Axial on the move again following our trusty partners at Poison Spyder Customs to Virginia City to explore the oldest Silver mining town in Nevada. The “Bucket of Blood” Saloon will be one of the highlights, known for its violence back when the mining town was running at full steam.

Friday July 18th will be qualifying day for the Hellsgate Grand Prix, an Unlimited 4wd Racing event to be held at Wild West Motorsports park. It will also be the day Axial and CKRC set up a booth for Saturdays racing action.

Saturday July 19th Axcial and CKRC will be on site with a booth showing off Axial R/C vehicles to the masses that arrive to spectate the inaugural Hellsgate Grand Prix. The Hellsgate Grand Prix will provide a ton of entertainment all day long with sidexside racing, Unlimited 4wd racing and the Deathbox derby.

For all the details on this inaugural event, please visit www.silverstatejamboree.com

About Carrera Performance Group LLc.

Off-Road History: Jeff became an “off-roader” in 1975 with his first dirt bike, a Honda Mini Trail 50. His parents were members of an off-road club called the “Looney Duners” in the 70s and 80s and many of his childhood weekends were spent out at Glamis, where his step-mother’s father had a business called “Boardmanville Trading Post”. Growing up in Menifee, California afforded Jeff the opportunity to do a lot of motorcycle riding. He met his wife, Angie, in high school and after graduation, they began riding trails and camping around Southern California. They raised both of their children in the back of Jeeps and Angie recalls changing many a diaper in the front seat of one. They have owned Jeeps and other off-road vehicles continuously throughout their 22 year marriage and have founded several off-road clubs including the Safari Club, Riverside Off-Kamber Club and Inland Jeep Freeks.

Racing: Jeff began racing BMX bikes at the age of 10. He has raced under many sanctioning bodies in several different classes. He has raced Best in the Desert, MORE, SCORE, and MDR series’. He has raced Jeepspeed, class 3000 and class 4400. He has written rules for BITD class 3000 and 4400, as well as rules for Side x Side racing under the International Side x Side Association (ISA). He has created two different sanctioning bodies for racing, the California Rock Crawlers Association (CRCA) and Ultra4 Racing. He is co-founder of the world famous “King of the Hammers” race held in Johnson Valley, CA each February.

Jeff has also developed and published strategic plans for the Off-Road Business Association and the California Motorized Recreation Council on Johnson Valley. In addition, he is a regular contributor to OffRoadPress.com and SEMA E-news. He contributes freelance for Crawl Magazine, DirtSports Magazine, Pirate4x4.com and Off-Road Industry Magazine. In 2013 Jeff Knoll published a whitepaper called “Common Ground” that became the basis for Legislation that passed the House of Representatives and as of this writing is being debated in the Senate. The bill would establish the first of its kind Congressional protected OHV area, and save the largest OHV area in the United States

About Axial

History
Founded in 2005, Axial R/C, Inc. has quickly become a global brand leader of hobby grade radio controlled products. We manufacture chassis and accessory products to the highest quality standards, with design emphasis on rugged construction and scale realism. Axial is regularly involved in local and national events which allow us to keep our finger on the pulse of R/C culture, thus earning us many awards over time, including “Best Truck”, “Most Innovative”, “Best Engineered Product of the Year”, and “People’s Choice.” Axial and the talented staff behind the brand live and breathe R/C, striving for excellence year after year.

MISSION
Axial is a company of enthusiasts for enthusiasts. The passion for the automobile runs deep within the Axial team. The brand itself is a culmination of a top shelf design team coupled with an executive and marketing staff with their finger on the pulse of what is hot and trending in the world of motorsports. Here at Axial we pride ourselves on developing extremely high end radio control models of vehicles that you are likely to see in the great outdoors. These models are designed to generate a tremendous amount of reliable fun that can be experienced by the whole family. Our design team prides themselves on marrying real scale looks with top level performance. Our marketing team ensures Axial is on the forefront by developing partnerships with top quality brands of the full size enthusiast market. Whether you are a beginner looking to further your knowledge about basic vehicle dynamics or a seasoned hobby veteran, Axial offers a platform for you to personalize and enjoy in every environment. The Axial team encourages you to get outside and have some family fun.

2014 King Of The Hammers has Great Results for Currie Racing

Currie_020_webc0c866.1a

Johnson Valley, CA. 2-10-14 – Casey Currie returned for the 2014 Griffin King of the Hammers this past weekend, expectations for a win may not have been met, but the odds of finishing the race were on Curries side. The week long event took place in Johnson Valley, CA where over 40,000 off-road/rock crawling enthusiasts flocked to watch 158 entries take their chance at the 150 mile brutal course.

After Curries 3rd place finish in Wednesdays UTV race, he helped his uncle, John Currie prepare for Thursdays Every Man Challenge. John qualified 1st for the race. Just miles into the start of the race, John gained a significant lead on the other competitors and continued to hold that lead all the way to the finish.

“We make sure that racing is fun for our entire family and it was great to see my Uncle as well as my brother finish on the podium.” Stated Casey Currie. “Knowing that my uncle won the EMC in the same vehicle I raced on Friday solidified my concerns on being a top competitor for the King of the Hammers race.”

Casey qualified the #88 Ultra 4 truck in the 44th starting position. The race began at 8am sharp and once on the course, Currie set a steady pace for the first lap. The first lap of the race consisted of dry lake-beds, sand washes and dunes. Currie finished the lap with no major issues and came into the main pit physically in the 20th position.

Laps 2 and 3 were more demanding and difficult with the course making its way through Clawhammer, Wrecking Ball, Chocolate Thunder and more. These laps would take there toll on numerous Ultra 4’s. Some out of the race, others rolled over and giving it all they have to get back on all fours. Currie and co-rider, Oren managed to make the right decision when making their way up the waterfalls.

“It is important to have a co-rider with you that is smart, calm and can assess the situation. This is just what Oren does.” Said Currie.
Currie_006_web.1a

As Currie made his way up “Backdoor” one of the hardest obstacles of the course, Oren had the challenge of guiding Currie up the slippery rocks. Other stuck vehicles would block the best lines and another vehicle would roll on its lid right next to them. This would be the only part of the course that would set the team back on time, but it wasn’t long before they made their way to the top and continued towards the finish.

In ten hours and 50 minutes, Currie and Oren crossed the finish line. Once at the finish the celebration was well deserved as the team got the results of a 14th place finish. This was worth celebrating since the #88 Ultra 4 was the first vehicle to come in that had only 14inches of travel, where as all the other finished had 20inches.

“We couldn’t be happier with our finish. It was a long day out there and the course was rough. The ruts were huge and dealing with other stuck competitors was a challenge. There is always the chance that they can take you out as well. Finishing in the top 15 out 158 speaks volumes of our team and the vehicle. Big thanks to everyone who puts this race together and on a great week of racing.” Stated Currie.

Be sure to follow Casey on all his social media outlets:
Twitter
https://twitter.com/CaseyCurrie

Instagram
http://instagram.com/caseycurrie

Facebook
https://www.facebook.com/OfficialCaseyCurrie

Axial – The Official R/C vehicles of Ultra4 Racing – King of the Hammers 2014

blog_axial_koh2014

FOR IMMEDIATE RELEASE:
(Irvine, CA) January 10, 2014.

Axial R/C Inc., A subsidiary of Hobbico Inc., is proud to announce Axial as the Official R/C Vehicles of Ultra4 / King of the Hammers for 2014.

Ultra4 Racing is the latest and greatest off road motorsport event on earth. This style of racing challenges man to a duel with the elements. Unlike standard off road racing in a stadium or in the wide open desert, Ultra4 vehicles face challenges that no other motorsport demands. Competitors are not only made to cross vast areas of open desert, they also travel up boulder strewn canyons and negotiate terrain that appears impassable. To compete in such a demanding environment, competitors build custom four wheel drive vehicles that are made to crawl over the harshest terrain, then conquer the wide open desert at exhilarating triple digit speeds. This element of automotive enthusiasm is precisely what Axial R/C has set out to deliver in 1:10 scale, so the relationship between Axial R/C and Ultra4 is a very natural fit.

Axial’s roots are directly tied to motorsports, especially competitive rock crawling. As full size competitive rock crawling transcended into what is now rock racing, the sport became globally recognized in a short five years, most notably the King of the Hammers [KOH] held annually in Johnson Valley, California. Axial followed suite with its own version of vehicles that translated well within this segment of the off road community. Axial has been very offroad lifestyle driven and fits perfectly with Ultra4 and the King of the Hammers event which is the mecca of enthusiasts pushing the boundaries of rock racing. Axial will be on site at the 2014 King of the Hammers offering enthusiasts an opportunity to experience the endless fun that these rock racing and trail navigating R/Cs have to offer.

On the Saturday following KOH [Feb 8th], there will be a radio controlled version of King of the Hammers as Axial hosts the RECON Ultra4 G6 at King of the Hammers.

Axial RECON Ultra4 G6 at King of the Hammers
When: Feb. 8 – 12:00 Noon
Where: (GPS- N34 24.927, W116 31.090) just west of Hammer Town at the base of the mountain.

R/C motorsports joins full size motorsports once again as Axial joins forces with Ultra4 / King of the Hammers. 2014 will once again see Axial bring the RECON G6 Series along for the full experience. Axial has teamed with full size motorsports in the past and is doing it again in Johnson Valley, Ca. ,on Saturday Feb. 8th, the day after the King of the Hammers main event. This is the last event on the 2014 KOH schedule starting at noon on Saturday, if you own an Axial R/C, come out and get your fix in this historic RECON Ultra4 G6. The RECON G6 series is made up of R/C endurance events featuring man and scale machine tackling the elements, a true test for your R/C vehicle with a major emphasis on a family fun atmosphere. The object is to conquer the course set forth by RECON G6 mastermind Brian Parker. For more information on this event, please click here.

About Axial
Founded in 2005, Axial R/C, Inc. has quickly became a global brand leader of hobby grade radio controlled products as Axial is a company of enthusiasts for enthusiasts. We manufacture chassis and accessory products predominantly for the Rock Crawling and Overland Adventure segments, with design emphasis on rugged construction and scale realism. Axial is regularly involved in local and national events which allow us to keep our finger on the pulse of R/C culture, thus earning us awards every year from 2007 through 2010, including “Best Truck”, “Most Innovative”, “Best Engineered Product of the Year”, and “People’s Choice.” For more information on Axial and Axial products please visit www.axialracing.comtwitter.com/axialracingfacebook.com/axialincyoutube.com/axialvideos

About Ultra4
Ultra4 Racing is the official website of Hammerking Productions. The founders of Hammerking are the force behind the toughest one-day off-road race on the planet: King of The Hammers. King of the Hammers takes place each year in February, on public lands in Johnson Valley, CA. The race has evolved from 12 teams racing for bragging rights and a case of beer, to more than 150 teams competing before thousands of fans both live and online. Due to the incredible success of King of the Hammers, Hammerking has created an equally difficult off-road endurance race called The Stampede which occurs annually in Reno, NV.

In addition to these races, Hammerking has established a racing class known as the Ultra4 class. The defining characteristic of this class is that all cars must be capable of 4-wheel drive. Beyond that, the class is unlimited, which means these cars come in all shapes and sizes and are capable of speeds over 100+ MPH and still contain gear ratios as low as 100 to 1 for technical rock crawling.

To give these cars and their drivers a chance to showcase their unique capabilities, Hammerking has formed the Ultra4 Racing series. The series challenges drivers to compete in a wide variety of terrain from endurance desert racing to competition-style rock crawls to short course racing. Hammerking currently produces five of the six races in the series on their own. The races take place on both public lands and in private motorsports parks across the country including: Exit 28 Motorsports Park in Nevada, Rausch Creek in Pennsylvania and Miller Motorsports Park in Utah.

Hammerking Productions has also produced three full-length feature films chronicling the first three King of the Hammers races. These award winning movies have helped shine a spotlight on this new form of racing throughout the world. Currently, fans are eagerly awaiting the release of Hammerking’s fourth production which will be coming to theaters and DVD by mid 2011.

If you would like to know more about Hammerking, Ultra4, the races produced and/or the movies created, please visit www.ultra4racing.comtwitter.com/Ultra4racingfacebook.com/Ultra4Racingyoutube.com/HeavyMetalConcepts

Contact:

Scott G.
Marketing – Special Projects
Axial R/C Inc.,
8 Goodyear, Suite 125
Irvine, CA 92618
email: scottg@axialracing.com
cell: 949-433-2189

###

Axial RECON Ultra4 G6 2014 at King of the Hammers

blog_recong6_koh

Axial RECON Ultra4 G6 at King of the Hammers

Axial Racing & RECON Crawlers has brought r/c enthusiasts Big Events since 2007. The Axial West Coast Championships started the r/c crawling “Big Events” and was the first to ever have qualifying rounds and LCQ’s. Axial Racing and RECON Crawlers teamed up again to bring r/c enthusiasts and their families an r/c genre that has swept the World, known as the RECON G6. The RECON G6 is more than an event, it’s a Life Style. The King of the Hammers (KOH) and Ultra4 racing is also a life style and they are going to be getting their R/C scaler fix, in The Axial RECON G6. This is the last event on the 2014 KOH schedule starting at noon on Saturday, if you own an Axial R/C, come out and get your fix in this 2nd annual Axial RECON Ultra4 G6.

Axial RECON Ultra4 G6 Intel

2014 Axial RECON G6 Adventure Series Event #1

When – February 8, 2014
Where – King of the Hammers (exact location TBA soon)
Why – Because we’re G6′n and everyone knows it.
Drivers Meeting / Stage line up to start at high noon or 12pm.
Stage Start following the National Anthem. (12:30+/-)
G-Fee – $25.00
15 and Under – $15.00

Bringing a power bar or Monster Ultra Zeros to G-Central is not mandatory, but highly recommended.

-A tow strap is mandatory. This can be a lanyard or shoe lace.
-5 scale items are mandatory. This may include side mirrors, seats, sleeping bags, etc.
-5 medieval scale items are not mandatory, but highly recommended. This could be a sword, shield, hat etc.
-Running the number and name of your favorite Ultra4 racer is not mandatory, but highly recommended.
-A spare tire is not mandatory, but highly recommended.
-A winch is not mandatory, but highly recommended.

If you missed the first ever Axial RECON Ultra 4 G6, don’t miss this one. There will be more of everything, including all the new 2014 RECON G6 classes and awards.

Classes –

- 1.9 Adventurist Class – This class is for all scalers using 1.9 size wheels & tires. It doesn’t matter your driving ability or your truck’s capability, everyone and every truck is capable of finding adventure here.

- 2.2 Adventurist – This class is for all scalers using 2.2 size wheels & tires. If you like big tires, this is your class. The 2.2 Adventurist will face bigger challenges, and their driving ability and scaler capability will be tested, as well. The 2.2 Adventurist has become a premiere class in the RECON G6.

- Expedition Class – “NEW” for 2014 and available at the Birthday Bash G6, – This class is for 6×6’s and scalers with trailers. This class will have more mandatory scale items and is geared towards the builders who enjoy the challenges of driving a 6×6 Truck or towing a trailer. Wheel and tire size are restricted to 1.9’s. Tires must be scale licensed or scale knock-offs. Expedition 6×6’s and G-Rides with trailers will each be awarded.

- RECON Ready Wrangler Modified Class – “NEW” for 2014 and available at the Birthday Bash G6, – This class is for the new Axial Jeep Wrangler G6 kit. Drivers are allowed to run any motor / esc combination, servo of your choice, any 1.9 tire / wheel combination, & battery of your choice. Rear steer and dig are not mandatory, but highly recommended. A winch and Pull Pal are not mandatory, but highly recommended. No AR60 or Wroncho style axles. The Stock body, frame rails, transmission case, and cage must be used. Stock or upgraded parts for the Axial SCX10 may be used, including transmission cases, axle housings, drivelines, steering knuckles, C’s, etcetera. Drivers finding adventure in the RECON Ready Wrangler Modified Class are eligible for a new kit & swag package.

- RECON G6 Driving Diva of the Day Award – “New” for 2014 & available at the Birthday Bash G6,- The best 1.9 Adventurist and 2.2 Adventurist female driver will be receive an award for their efforts.

- RECON G6 Driving Durty Award – “New” for 2014 & available at the Birthday Bash G6. This award will be awarded for the top 1.9 Adventurist & 2.2 Adventurist 15 years or younger.

- Event Credentials and Finishing Tags – “New” for 2014 and available starting February of 2014, – All drivers that pre-register for a RECON G6, will receive event specific credentials to commemorate the RECON G6 they attend and all G6’ers will receive finishing tags upon completing the RECON G6 stage, because “finishing a RECON G6 is like winning a RECON G6.

Bring the Family. Bring your friends. Bring your sense of adventure. The 2014 Axial RECON Ultra4 G6 will have you on the edge of your scale adventure seat. Join us for all the King of the Hammers racing action, including racing action on Axial Blvd. Not only will there be an Axial Adventure trail, but new for 2014, Ultra 4 racing action. Do you like bragging rights? Do you like swag? Do you like being the fastest driver of the day? Night? Week? Then come experience Ultra 4 racing Axial 1/10 scale RECON style.

Come get your scale adventure fix, at the 2014 Axial RECON Ultra4 G6!

To Pre-register for this event, click here!

Please visit RECON on their web pages and FaceBook here….

RECONG6.com

RECON G6 Facebook

Full Option RTR Deadbolt

blog_deadbolt_option

Axial offers several optional upgrade parts for the RTR Deadbolt. Here is a quick run down of what is installed and why you may want to use these items.

A couple photos of the fully option RTR Deadbolt. Axial also offers clear replacement Deadbolt bodies, part number AX04039, for those that want to customize the look of their trucks.
DSC_0092

First option parts that can be seen here are the 2.2 Maxxis Trepador tires in our sticky R35 compound, part number AX12022. We also installed our VMS beadlock wheels, part number AX08061. We will cover more on the VMS wheels later on in this article.
DSC_0096

Body off shot!
DSC_0100

Next option part we installed is a 25t aluminum servo horn, part number AX30836. Axial’s HD aluminum servo horn provides more responsive steering with less chance of stripping the internal splines over the stock plastic servo horn. Clamping style head for secure mounting in high stress applications. Available in 23, 24 and 25 tooth spline counts.

Axial’s HD differential covers, part number AX30829. HD diff covers protect ring and pinion gears from being damaged by rocks, just like their 1:1 counterparts, all while adding a little bling to your ride.

Aluminum axle lockouts are another available option, part number AX30789. Axial’s aluminum axle lockouts are more rigid than the stock plastic lockouts, which will allow the vehicle to track better in all situations.

Another great upgrade is Axial’s aluminum shocks, part number AX30092. Aluminum shocks provide better dampening than the stock plastic shocks, especially when mated with our Delrin shock pistons. Aluminum shock bodies also dissipate heat better than the stock plastic bodies. Oversize 3.5mm shock shafts for rigidity. Great for high power applications and long run times. Axial also offer a complete line of various springs to fine tune your suspension as needed, see the complete parts list below for more info.

Another option part that is hiding behind the HD diff cover is Axial’s HD ring and pinion gears, part number AX30395. HD ring and pinion gears are more efficient than the stock aluminum ring and pinions. CNC machined for precision. Hardened steel for durability. Great for high power applications. Axial also offers hardened steel overdrive ring and pinion gear sets, part number AX30401, for a little extra wheel speed. We also offer an underdrive ring and pinion gear sets, part number AX30402, for a little more torque in binds.

Axial’s HD lower link mounts are another noteworthy upgrade, part number AX30830. Our HD lower link mounts allow users to fine tune ride height and wheelbase by providing more adjustment holes than the stock plastic units.

You can see a handful of options parts in this photo. First option is the aluminum knuckles, part number AX30760. Aluminum knuckles provide more responsive steering and help your vehicle track better at speeds and in the rocks. Another option shown is the Axial Aluminum C-hubs, part number AX30762. Aluminum C-hubs also help your vehicle track more consistently in all situations, especailly when used in conjunction with our aluminum knuckles. Also notice the AR60 universal axles, part number AX30780. Axial universal joint axles increase steering angle to 50 degrees, that’s 60% over the stock dogbone/drive cup setup. These universals provide smoother action for a higher performing, efficient drivetrain. The universal is oversized; typical for 1/8 scale vehicles and made of hardened steel so it’s capable of handling extreme power.

Our intention with this project was to build a solid axled basher that can handle a lot of power. Axial’s Vanguard Brushless System was the perfect fit to supply that power. The 2900KV brushless motor, part number AX24010, is more efficient that standard brushed motors and provides a lot more power for hill climbs and general monster truck style bashing over the stock set-up. Providing control for the brushless motor is our Vanguard ESC, part number AX24260. The Vanguard ESC has an array of features that can be programmed manually or with a Castle Link. Highlighted features include adjustable drag brake, lipo cutoff, traction control, motor timing, etc. Our Vanguard ESC is compatible with both brushed and brushless motors, so it can be run with either configuration. Standard Deans® Ultra Plug® battery connector included.

Another great upgrade is the Wraith Stage One link kit, part number AX30797. This kit is geared towards the Wraith, but also works great with the Deadbolt. Especially if you are going to compete at rock crawling competitions, as the wheelbase falls just under the 12 1/2″ max wheelbase limit. Our Stage One link Kit replaces all the stock plastic suspension links with high quality 7mm diameter aluminum links. Eliminates axle wrap and unwanted axle steer, especially in high power applications. Axial also offers machined heavy duty aluminum straight links, part number AX30790, to replace the stock plastic lower links as an alternative the the Stage One link kit.

Axial’s HD motor plate, part number AX30860. Our heavy duty motor plate is for any vehicle running our AX10 transmission. CNC machined from 4.5mm thick billet aluminum, with integrated heatsink fins to help motors run cooler on those all day expeditions. A must have for any R/C overland adventurist! Axial also offers 13t, 14t and 15t steel pinion gears and an 80t spur gear to give end users an array of gear ratios to choose from. Add more torque for low speed crawling to your Deadbolt by installing one of Axial’s optional brushed motors available in 27t and 55t configurations. Axial also offers a complete steel transmission gear set for even more durability, part number AX30708.

Once again for wheels we went with our VWS beadlocks, part number AX08061. VWS wheels allow users to tune foam set-ups and change tires at will for varying terrain and conditions. Another wheel option offered by Axial is our black 8 hole beadlock wheels, part number AX8097. These wheels offer a little wider overall stance which equals stability at high speeds. For low speed rock crawling you can increase your Deadbolt’s climbing abilities by adding Axial’s 2.2 Internal Weight Rings, part number AX30545. Add even more weight by utilizing Axial’s 2.2 Internal Wheel Weights for the Internal Wheel Weight Rings, part number AX30546.

You can see our R35 Ripsaw tires pictured here, part number AX12015. R35 Ripsaw tires offer both a realistic look for the image-conscious scale crawler and for those looking to up their performance game. This 2.2 Ripsaw offers an aggressive tread design, greater ground clearance, and is made from a R35 sticky compound. The VWS wheels include black aluminum rings, but I swapped those out for our Grey beadlock rings, part number AX08133, just to match the grey colored suspension links.

Complete Deadbolt option parts list:
AX8097 – 2.2 Black 8 Hole Beadlock Wheels (x2)
AX08061 – 2.2 VWS Beadlock Wheels (x2)
AX08133 – Grey VWS Beadlock Rings (x2)
AX08141 – 2.2 Trail Ready Beadlock Wheel – Black (x2)
AX08142 – 2.2 Trail Ready Beadlock Wheel – Black and Chrome (x2)
AX12015 – 2.2 R35 Ripsaw Tires (x2)
AX12022 – 2.2 Maxxis Trepador Tires (x2)
AX12021 – 2.2 BFGoodrich Krawler T/A Tires (x2)
AX30545 – 2.2 Internal Wheel Weight Rings (x2)
AX30546 – 2.2 Wheel Weight Inserts (x2)
AX30797 – Stage One Link Kit
AX30790 – Machined Heavy Duty Aluminum Straight Link 101mm (x2)
AX30469 – Machined Heavy Duty Aluminum High Clearance Upper Links (x2)
AX80057 – XR10 Linkage Set (x4 for all 8 links)
AX30395 – HD Ring and Pinion Gear Sets (stock gear ratio) (x2)
AX30401 – Overdrive HD Ring and Pinion Gear Sets (x2)
AX30402 – Underdrive HD Ring and Pinion Gear Sets (x2)
AX30571 – 13t Steel Pinion Gear
AX30569 – 14t Steel Pinion Gear
AX30573 – 15t Steel Pinion Gear
AX30665 – 80t Spur Gear
AX30708 – Steel Transmission Gear Set
AX30829 – HD Differential Covers (x2)
AX30860 – HD Motor Plate
AX30830 – HD Link Mounts (x2)
AX30834 – 23t HD Servo Horn
AX30835 – 24t HD Servo Horn
AX30836 – 25t HD Servo Horn
AX30762 – Aluminum Axle C-hub’s
AX30760 – Aluminum Knuckles
AX30789 – Aluminum Axle Lockouts
AX30092 – Aluminum Shocks (x2)
AX30780 – AR60 Universal Axle Set
AX24260 – AE-3 Vanguard ESC
AX24010 – Vanguard 2900KV Brushless Motor
AX24007 – 55 Turn Motor
AX24004 – 27 Turn Motor
AX04032 – Clear Ridgecrest Body
AX30223 – Black Springs 1.04 lbs/in (x2)
AX30224 – Purple Springs 1.43 lbs/in (x2)
AX30225 – Orange Springs 1.75 lbs/in (x2)
AX30218 – Red Springs 2.07 lbs/in (x2)
AX30219 – White Springs 2.47 lbs/in (x2)
AX30220 – Green Springs 2.85 lbs/in (x2)
AX30221 – Yellow Springs 3.27 lbs/in (x2)
AX30222 – Blue Springs 3.55 lbs/in (x2)