Axial Deadbolt AX90066 Simple Body and Bumper Mod

Axial Deadbolt AX90066 Simple Body and Bumper Mod
The Axial AX90066 Deadbolt is an extremely popular body style, and we’re constantly pulling spare plastic out of our parts bins to try and create a few simple body mods.

The first is something we’ve been asked about for a long time – why doesn’t the Deadbolt come with a rear bumper. Well, say no more – check out this great little how to on adding a simple rear bumper to the back of your Deadbolt.

TOOLS NEEDED:
1. 1.5mm Hex Wrench
2. 2.0mm Hex Wrench
3. Side cutters
4. Dremel (to help clean up the bumper)

LIST OF PARTS USED:
AX80125 Axial SCX10 Poison Spyder JK Brawler Lite Front Bumper

Step 1

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Here are the two parts we’ll be installing; a front bumper and bumper mount. We’ll use the original hardware included with your Deadbolt to re-mount the parts.

Step 2

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Using the side cutters, clip the hoop off the bumper. Here’s where you can use the Dremel to clean up the bumper. If you have a thin pair of side cutters, you might be able to clip close to the bumper and not require any Dremel work.

Step 3

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Remove the stock rear bumper and install the AX80125 mount. Use the stock hardware to lock it in place.

Step 4

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Slide your freshly modified rear bumper into the mount and secure with the stock hardware.

Step 5

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Set your body on top and examine your handiwork. Your Deadbolt now has a rear bumper that even includes light buckets!

Step 6

Axial Deadbolt AX90066 Simple Body and Bumper Mod
But wait – there’s more! If you have a set of D-rings lying around, you can add those to the rear bumper to help pull your buddies out if they get stuck!


This second mod came about after a couple of us found that getting to the rear body clips can be a bit of a pain if you have chunky hands. This mod will not only make it super easy to get to them, it also give provisions for adding a scale rear tire.

TOOLS NEEDED:
1. 2.0mm Hex Wrench
2. Side cutters
3. Dremel (to help clean up the bumper)

LIST OF PARTS USED:
AXA0147 M3x16mm Hex Socket Flat Head Screw
AXA1052 M3 Thin Nylon Locking Hex Nut
AXA0422 M2.6x6mm Hex Socket Tapping Button Screw
AX31305 TT-380 Rear Lower Cage and Tire Retainer
AX80130 Roll Cage Sides

Step 1

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Remove the body – as you can see, it’s a little tough getting to the rear body pins with sausage fingers.

Step 2

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Here are the parts you’ll need. Any spare tire will work with this mod (as long as it’s a 1.9). It’s also suggested that you remove the foam insert as well. You’ll see more about this later.

Step 3

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Mount the tire to the cage by inserting your 16mm screw through the washer, then through the tire. Note the orientation of the mount; this setup mounts the tire low in the bed for the best performance. If you want to allow a little more room for, say, some scale items, flip the plastic mount as shown in the picture below (you’ll need at least a 30mm screw to attach the rear tire).

Axial Deadbolt AX90066 Simple Body and Bumper Mod

Step 4

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Secure the tire in place with a M3 locknut. If you’re feeling really sassy, you can use the AX31320 Axial Bomber Rear Tire Hold Down for a super trick look!

Step 5

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Remove the screws from the stock cage (see the pretty red arrows). Make sure you remove them from BOTH sides of the Deadbolt.

Step 6

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Using the side cutters, chop off the rear part of the cage as shown. You can use a Dremel here to clean up the cut or just leave it be.

Step 7

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Attach your rear tire mount to the cage, flip it up and secure with the M2.6×6 screws. Tightening these down will help keep the rear cage in place, just be sure not to over-tighten them.

Step 8

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Lower the cage all the way to the body, and ‘pinch’ the tire in-between the cage. This is where a tire without the foam insert will help hold the flip-cage in place a little better.

Step 9

Axial Deadbolt AX90066 Simple Body and Bumper Mod
Now, swing the cage up to install the body pins. Brilliant, right?

John Schultz’s Winning Deadbolt

JohnSchultz_WP_Title_IMG

Fresh off the tarmac from the 2015 No Limit RC Monster Truck World Finals held at Dennis Anderson’s Diggers Dungeon in Poplar North Carolina, John Schultz, Axial Ambassador, dropped off his custom built Deadbolt Monster Truck conversion at Axial HQ for a closer look.  It’s important to note, Solid Axle was the biggest class in attendance, 70 trucks raced and a total of 80 trucks present, many of which featured Axial’s AR60 axles.

JohnS_BKT_Truck_WP-6

Upon first peek it might be hard to spot the Deadbolt backbone, but upon a second glance it’ll be more obvious, as will the dusting of Wraith and Yeti parts. We’ll be featuring a more in-depth build report on the truck shortly. In the meantime, here’s a quick parts list and detailed photos of the truck. Lets not forget photos, CLICK HERE for more photos.

JohnS_BKT_Truck_WP-5 JohnS_BKT_Truck_WP-4 JohnS_BKT_Truck_WP-3 JohnS_BKT_Truck_WP-2 JohnS_BKT_Truck_WP-7 JohnS_BKT_Truck_WP-8 JohnS_BKT_Truck_WP-1

Axial Parts List:

AX31109 – Yeti™ Rear 4 Link Set, F&R

AX30782 – Wraith Rear Sway Bar Set (Soft, Medium, Firm)

AX30781 – Wraith Front Sway Bar Set (Soft, Medium, Firm)

AX30708 – AX10 Locked Transmission – Complete Metal Gear Set – Steel (3pcs)

AX30829 – AR60 OCP Machined Low-Profile Differential Cover (Hard Anodized)

AX30830 – AR60 OCP Machined Link Mounts (Hard Anodized) (2pcs)

AX30836 – Aluminum Servo Horn 25T (Hard Anodized)

AX30780 – AR60 OCP Universal Axle Set F&R

AX30789 – AR60 OCP Aluminum Straight Axle Hub Carrier (2pcs)

AX30395 – Heavy Duty Bevel Gear Set – 38T/13T (Rear Axle)

AX30401 – Heavy Duty Bevel Gear Set – 36T/14T (Front Axle, Overdrive)

AX30760 – XR10 Aluminum Steering Knuckle (Black) (2pcs)

AX30762 – XR10 Aluminum C-Hub Carrier (Black) (2pcs)

Other Parts:

Tires – 10114-02 – Pro-Line Racing Destroyer 2.6” Solid Axle Monster Tire F&R

Wheels – Clod Buster Rims and Adapters F&R

HPI – 88055 - Wheelie King Axle Wideners F&R

HPI – 6589 - Wheelie King Red/Soft Springs

HPI – 87600 – Wheelie King Differentials

Body – 3252-00 – Pro-Line Racing Ford F-250 Body

Graphics/Paint – BKT Ride Truck Graphics

ESC/Motor – 3087 – Novak Electronics – Crusher ESC w/4PHD 4X4 SCT BL Motor

Battery – DTXC1964 – Duratrax – 2s 5000mAh 35c LiPo

Servo – Savox – SV1271SG