Yeti Pre-run Checklist – Read Before You Run

blog_yetiprerun

Now that the Axial Yeti is hitting hobby store shelves, we are hearing of more “Yeti sightings” being recorded! That being said we wanted to take a few minutes to help you get familiar with this new platform! First and foremost, let’s go over what to look for when you first pull it out of the box. As with any new RTR R/C vehicle, you should check everything over carefully before installing a battery and heading off to your local bash spot. RTR means “ready to run”, but even then there are certain things you should check before actually running your new “RTR” R/C. For this blog post we will cover unboxing your new Yeti, and what to look for before driving it for the first time.

Checklist:

1. Check and make sure the wheel nuts are properly torqued down on all four corners of the vehicle after you pull it out of the box. No need to get crazy and over tighten them, just make sure they are good and snug.

DSC_0432

2. Adjust the height of the battery tray to fit the battery packs you have, or that you plan on running.You want to make sure the battery is held firmly in place so it can’t move around while you are driving. If the battery can move around in the chassis while you are driving the Yeti, it can cause erratic or inconsistent handling.

DSC_0440

3. Next we added a little foam to the battery tray to stop the battery from sliding back and forth after you have adjusted the height in the previous step. We cut up an old tire foam and used a little at both ends of the battery. Shoe Goo can be used to hold the foam in place so it stays put during battery changes.

DSC_0437

4. Check all drive shaft set screws prior to your first run to ensure they are tight. You will also want to check these after your first battery pack as well, just to make sure they are still properly seated.

DSC_0441

For the front output, turn the front tires to the passenger side. Then, you can access the set screw from the driver’s side with a long 2mm driver as shown.

DSC_0429

DSC_0450

This covers the initial inspection before you run your Yeti for the first time. Taking a few minutes to go over this list, as well as giving the entire vehicle a quick visual check, will definitely give you a better experience. We will have more maintenance tips and tricks coming soon as well! Stay tuned!!

Axialfest 2014 – Report By Skeeno

blog_axialfestreport

Well it was that time of year again, Axialfest Time!  Did you make it out?  The Skeenos did, and it was an awesome way to spend Father’s Day Weekend.  Skeeno Jr and I had another great time.  If you didn’t make it, you better make plans for next year.

Here’s how it went down around the Skeenos.

DSCF1002

First thing was that Axialfest 2014 fell a week earlier than usual.  For me, that meant I had to do a little preplanning, since I would be working up until Friday when Axialfest started.  I didn’t want to be rushed to set up camp the day of the event, so I met Mr. Parker up at Cisco Grove after work one day and set up camp a little early.

DSCF1003

Red Rocket kept an eye on G Camp during the week while I was at work.  Thanks Red Rocket.  You did a stellar job.

DSCF1073 (2)

For the rest of the week, it was a little hard to focus on work knowing good times were just around the corner. Finally, Friday came and I was able to sneak away from work early, scoop up Skeeno Jr. and head up to Axialfest 2014.  These signs made it easy to find the new location at Cisco Grove Campground.

DSCF1010

First thing I saw was Mr. Tree strutting around. He was actually prepping the mud pit. Sweet shoes big boy.

DSCF1022

Since the buckets were heavy, Tree got some assistance from Mini Meeks.

DSCF1019

I walked around G Central and saw lots of familiar faces. Here I saw Bender, Rodney, and Sam Trujillo of Rock Armor chatting.

DSCF1020

I also saw Anthony Rivas.  He is a huge part of the G Crew, Parker’s right hand man.  He was actually smiling.  It must have been because the craziness hadn’t started yet.

DSCF1013

A few people were still driving on the Trials Course.  Here a Toyota runs through the Axial Alley.

DSCF1006Axial Alley was a popular spot to run.

DSCF1004 (2)

Before the start of the the G6, I had some business to conduct.  I was the official cook of the G Crew for Axialfest. I had this view for every meal.

WP_20140613_003

4 pounds of Tri Tip should keep the G Crew happy.

WP_20140613_007

My cooking must have been ok, because the G Crew seemed to enjoy it.  Rivas didn’t get to eat with us because he was tasked with manning G Central all weekend.  Don’t worry, we sent him up a plate.

DSCF1003 (2)

Skeeno Jr hustled to get her new G6 Jeep ready for Stage One. It was its first real usage other than street testing back home.

DSCF1017 (2)

Turnout was pretty impressive.  I mean, it’s always a good turnout, but Axialfest 2014 shattered attendance records.  Could we see 500 next year?  I think so.

DSCF1027

DSCF1092

After the driver’s meeting it was go time. First stage was a night run, so you better have packed your LEDs.

WP_20140613_009

It was a little crowded for a minute until the drivers spread out. Skeeno Jr. was anxious to get some real wheel time in.

DSCF1049Skeeno Jr’s new G6 Jeep did awesome on its inaugural run. She ran it completely stock with a 55T motor and 2S Lipo. It did AWESOME and finished without any issues. This G6 Jeep is the Bomb!

DSCF1054

It did so well, Skeeno Jr. had to slow down and wait for some slower traffic.

DSCF1056

That’s Trail Marker 216.  Stage one had 500 for the Adventurists and 1000 for the Ultras.  That is maximum drive time.  I hope you remembered to pack some extra batteries.

DSCF1080Here’s Skeeno Jr. steering clear of the river.  Her ESC isn’t waterproof…yet.

WP_20140615_002

Stage 1 went late into the night.

WP_20140614_001

Good morning, time for breakfast burritos.

DSCF1027 (2)

There’s that mud pit.  Some people were a little scared to get dirty.

DSCF1025

Don’t worry, he took the first run a little slow, but then he got her dirty.

DSCF1020 (2)

Others were so eager to fling some mud that they flung themselves.

DSCF1021Old Blue Bastard is never afraid of getting a little muddy.

DSCF1038

The bridges on the Trails Challenge were quite challenging.  You needed your A-game to pull some of these lines.

DSCF1047This suspension bridge bucked off everyone.

DSCF1035

This kit didn’t need the Pull Pal RW60 to get up the hill climb even though this hill was steep and silty.

DSCF1056 (2)

I saw some sweet custom 1:10 Trasharoos.  Do you have monogrammed accessories on your kit?

DSCF1065 (2)

Of course the Bautista Terror was at Axialfest.  It goes to all RECON G6 events.  It’s also known as the Driveshaft Killer. It’s claimed more than one of mine.

WP_20140614_014

Stage 2 took us back down by the river.

WP_20140614_009

Lunch time, Beer Brat, anyone?

DSCF1148

Skeeno Jr. and I kept seeing these Yetis.  They were a little creepy. Turns out that the Yetis were a promotional gimmick for the new Axial YETI. I’m sure you’ve seen it.  If you haven’t, go check it out here: http://www.axialracing.com/blog_posts/1073909414

DSCF1070

Stage 3 of the RECON G6 was a treasure hunt to capture a Yeti.  Successful hunters got a sneek peek before the Yeti was announced to the public.  Here, a lucky G6er drives his Yeti back to G Central.

DSCF1075One thing I love about Axialfest and all the RECON G6 events is the families that come out.  How many times have you seen daughters come out to drive an RC car?  How about whole families?  It’s quite common at Axialfest.

DSCF1084 (2)The Meeks are old RECON G6ers from the 2.2 comp days. Now the whole clan comes out to drive.  How cool is that?

DSCF1078

Here’s another Mother/Daughter combo. Cassie’s daughter was a little camera shy.

DSCF1089Hold up, what is this?  Many vendors made their way up to enjoy and support Axialfest, but Werty Made Products did it right. They brought a movie projector and inflatable hot tub to relax in after a long day of driving.

DSCF1092 (2)

DSCF1093 (2)

The rocks down at the river were slickery from years of polishing.  Once your tires were wet, these simple climbs became difficult.

DSCF1102Even if you couldn’t make an obstacle, there was always someone to lend a hand.  Here a driver gets a little tug over a tough patch.

DSCF1111

There’s HoyFab’s 6×6 waiting its turn.  When you are trail running, sometimes you have to be patient.

DSCF1081Dropping in down by the river.  Slick rock and sand is a nasty combination.

DSCF4015Down at RPP’s Rattle Snake Creek, some drivers had to call for help if they didn’t pack a raft.

DSCF4002

Luckily, CKRC gave free rides to anyone in need.

DSCF4003Skeeno Jr. wasn’t skeerd, she jumped right in and pulled her kit to the safety of the far bank.

DSCF4008

After the river crossing, Skeeno Jr. panned for a little gold.  She found a nice nugget and put it in her scale Trasharoo.

DSCF4016

After sitting in the hot tub all night, Werty considers sitting in the stream. That, or he was taking some pictures of his trucks.

WP_20140614_008

Stage 3 and still smiling.  Axialfest must be a lasting good time.

DSCF1108

Well that just about wraps up the Skeeno report.  Another year and another Axialfest in the books. It was a great time seeing old friends, making new friends, and making memories with my daughter.  Skeeno Jr. and I are already counting down the days until Axialfest 2015.

DSCF1107

The Driver of the Day Awards were waiting back at G Central.  Did you get one?  Look for a complete report on winners in an upcoming blog.

Full Option RTR Deadbolt

blog_deadbolt_option

Axial offers several optional upgrade parts for the RTR Deadbolt. Here is a quick run down of what is installed and why you may want to use these items.

A couple photos of the fully option RTR Deadbolt. Axial also offers clear replacement Deadbolt bodies, part number AX04039, for those that want to customize the look of their trucks.
DSC_0092

First option parts that can be seen here are the 2.2 Maxxis Trepador tires in our sticky R35 compound, part number AX12022. We also installed our VMS beadlock wheels, part number AX08061. We will cover more on the VMS wheels later on in this article.
DSC_0096

Body off shot!
DSC_0100

Next option part we installed is a 25t aluminum servo horn, part number AX30836. Axial’s HD aluminum servo horn provides more responsive steering with less chance of stripping the internal splines over the stock plastic servo horn. Clamping style head for secure mounting in high stress applications. Available in 23, 24 and 25 tooth spline counts.

Axial’s HD differential covers, part number AX30829. HD diff covers protect ring and pinion gears from being damaged by rocks, just like their 1:1 counterparts, all while adding a little bling to your ride.

Aluminum axle lockouts are another available option, part number AX30789. Axial’s aluminum axle lockouts are more rigid than the stock plastic lockouts, which will allow the vehicle to track better in all situations.

Another great upgrade is Axial’s aluminum shocks, part number AX30092. Aluminum shocks provide better dampening than the stock plastic shocks, especially when mated with our Delrin shock pistons. Aluminum shock bodies also dissipate heat better than the stock plastic bodies. Oversize 3.5mm shock shafts for rigidity. Great for high power applications and long run times. Axial also offer a complete line of various springs to fine tune your suspension as needed, see the complete parts list below for more info.

Another option part that is hiding behind the HD diff cover is Axial’s HD ring and pinion gears, part number AX30395. HD ring and pinion gears are more efficient than the stock aluminum ring and pinions. CNC machined for precision. Hardened steel for durability. Great for high power applications. Axial also offers hardened steel overdrive ring and pinion gear sets, part number AX30401, for a little extra wheel speed. We also offer an underdrive ring and pinion gear sets, part number AX30402, for a little more torque in binds.

Axial’s HD lower link mounts are another noteworthy upgrade, part number AX30830. Our HD lower link mounts allow users to fine tune ride height and wheelbase by providing more adjustment holes than the stock plastic units.

You can see a handful of options parts in this photo. First option is the aluminum knuckles, part number AX30760. Aluminum knuckles provide more responsive steering and help your vehicle track better at speeds and in the rocks. Another option shown is the Axial Aluminum C-hubs, part number AX30762. Aluminum C-hubs also help your vehicle track more consistently in all situations, especailly when used in conjunction with our aluminum knuckles. Also notice the AR60 universal axles, part number AX30780. Axial universal joint axles increase steering angle to 50 degrees, that’s 60% over the stock dogbone/drive cup setup. These universals provide smoother action for a higher performing, efficient drivetrain. The universal is oversized; typical for 1/8 scale vehicles and made of hardened steel so it’s capable of handling extreme power.

Our intention with this project was to build a solid axled basher that can handle a lot of power. Axial’s Vanguard Brushless System was the perfect fit to supply that power. The 2900KV brushless motor, part number AX24010, is more efficient that standard brushed motors and provides a lot more power for hill climbs and general monster truck style bashing over the stock set-up. Providing control for the brushless motor is our Vanguard ESC, part number AX24260. The Vanguard ESC has an array of features that can be programmed manually or with a Castle Link. Highlighted features include adjustable drag brake, lipo cutoff, traction control, motor timing, etc. Our Vanguard ESC is compatible with both brushed and brushless motors, so it can be run with either configuration. Standard Deans® Ultra Plug® battery connector included.

Another great upgrade is the Wraith Stage One link kit, part number AX30797. This kit is geared towards the Wraith, but also works great with the Deadbolt. Especially if you are going to compete at rock crawling competitions, as the wheelbase falls just under the 12 1/2″ max wheelbase limit. Our Stage One link Kit replaces all the stock plastic suspension links with high quality 7mm diameter aluminum links. Eliminates axle wrap and unwanted axle steer, especially in high power applications. Axial also offers machined heavy duty aluminum straight links, part number AX30790, to replace the stock plastic lower links as an alternative the the Stage One link kit.

Axial’s HD motor plate, part number AX30860. Our heavy duty motor plate is for any vehicle running our AX10 transmission. CNC machined from 4.5mm thick billet aluminum, with integrated heatsink fins to help motors run cooler on those all day expeditions. A must have for any R/C overland adventurist! Axial also offers 13t, 14t and 15t steel pinion gears and an 80t spur gear to give end users an array of gear ratios to choose from. Add more torque for low speed crawling to your Deadbolt by installing one of Axial’s optional brushed motors available in 27t and 55t configurations. Axial also offers a complete steel transmission gear set for even more durability, part number AX30708.

Once again for wheels we went with our VWS beadlocks, part number AX08061. VWS wheels allow users to tune foam set-ups and change tires at will for varying terrain and conditions. Another wheel option offered by Axial is our black 8 hole beadlock wheels, part number AX8097. These wheels offer a little wider overall stance which equals stability at high speeds. For low speed rock crawling you can increase your Deadbolt’s climbing abilities by adding Axial’s 2.2 Internal Weight Rings, part number AX30545. Add even more weight by utilizing Axial’s 2.2 Internal Wheel Weights for the Internal Wheel Weight Rings, part number AX30546.

You can see our R35 Ripsaw tires pictured here, part number AX12015. R35 Ripsaw tires offer both a realistic look for the image-conscious scale crawler and for those looking to up their performance game. This 2.2 Ripsaw offers an aggressive tread design, greater ground clearance, and is made from a R35 sticky compound. The VWS wheels include black aluminum rings, but I swapped those out for our Grey beadlock rings, part number AX08133, just to match the grey colored suspension links.

Complete Deadbolt option parts list:
AX8097 – 2.2 Black 8 Hole Beadlock Wheels (x2)
AX08061 – 2.2 VWS Beadlock Wheels (x2)
AX08133 – Grey VWS Beadlock Rings (x2)
AX08141 – 2.2 Trail Ready Beadlock Wheel – Black (x2)
AX08142 – 2.2 Trail Ready Beadlock Wheel – Black and Chrome (x2)
AX12015 – 2.2 R35 Ripsaw Tires (x2)
AX12022 – 2.2 Maxxis Trepador Tires (x2)
AX12021 – 2.2 BFGoodrich Krawler T/A Tires (x2)
AX30545 – 2.2 Internal Wheel Weight Rings (x2)
AX30546 – 2.2 Wheel Weight Inserts (x2)
AX30797 – Stage One Link Kit
AX30790 – Machined Heavy Duty Aluminum Straight Link 101mm (x2)
AX30469 – Machined Heavy Duty Aluminum High Clearance Upper Links (x2)
AX80057 – XR10 Linkage Set (x4 for all 8 links)
AX30395 – HD Ring and Pinion Gear Sets (stock gear ratio) (x2)
AX30401 – Overdrive HD Ring and Pinion Gear Sets (x2)
AX30402 – Underdrive HD Ring and Pinion Gear Sets (x2)
AX30571 – 13t Steel Pinion Gear
AX30569 – 14t Steel Pinion Gear
AX30573 – 15t Steel Pinion Gear
AX30665 – 80t Spur Gear
AX30708 – Steel Transmission Gear Set
AX30829 – HD Differential Covers (x2)
AX30860 – HD Motor Plate
AX30830 – HD Link Mounts (x2)
AX30834 – 23t HD Servo Horn
AX30835 – 24t HD Servo Horn
AX30836 – 25t HD Servo Horn
AX30762 – Aluminum Axle C-hub’s
AX30760 – Aluminum Knuckles
AX30789 – Aluminum Axle Lockouts
AX30092 – Aluminum Shocks (x2)
AX30780 – AR60 Universal Axle Set
AX24260 – AE-3 Vanguard ESC
AX24010 – Vanguard 2900KV Brushless Motor
AX24007 – 55 Turn Motor
AX24004 – 27 Turn Motor
AX04032 – Clear Ridgecrest Body
AX30223 – Black Springs 1.04 lbs/in (x2)
AX30224 – Purple Springs 1.43 lbs/in (x2)
AX30225 – Orange Springs 1.75 lbs/in (x2)
AX30218 – Red Springs 2.07 lbs/in (x2)
AX30219 – White Springs 2.47 lbs/in (x2)
AX30220 – Green Springs 2.85 lbs/in (x2)
AX30221 – Yellow Springs 3.27 lbs/in (x2)
AX30222 – Blue Springs 3.55 lbs/in (x2)

Axial’s AS-3 Servo Upgrade

blog_servo_mod_500x220

Axial’s AS-3 servo is standard equipment in all RTR Axial vehicles. We know most people hear the term “RTR servo” and they immediately think an “upgrade” is in order. But, this servo is actually very capable for an RTR servo, especially when used in conjunction with 1.9 wheels and tires. The AS-3 servo is a digital servo, it has metal gears and is rated at 150 ounces of torque at 6.0 volts. The one drawback that this servo does have is the main output shaft is supported by a plastic bushing rather than a bearing. After you have run a few battery packs through your RTR you may notice a little slop in the servo’s output shaft where the servo horn attaches. Once dirt gets in around the output shaft and bushing, it starts to wear the bushing fairly quickly. As the bushing wears the servo output shaft will develop some side to side play. Once it wears to a certain point your gear mesh will be compromised and you run the risk of stripping teeth off a servo gear. Luckily for us Fast Eddy Bearings has recognized that a simple inexpensive bearing can add a lot of life to that RTR servo, and eliminate these problems. This is the best “bang for your buck” mod you can make to any Axial RTR vehicle. It is a simple, inexpensive way to upgrade your Axial AS-3 RTR servo.

Remove the servo horn from the servo’s output shaft. Then, remove the servo from the front axle. You will want to unplug the servo from the receiver, just to make the switch less of a hassle. A shot of the servo, and the new 6x10x2.5mm bearing that will replace the bushing.
servo-bearing-013

Using a 1.5mm driver, loosen up the 4 small screws on the bottom of the servo case.
servo-bearing-018

You can leave the screws in the case, just make sure they are all loose.
servo-bearing-019

Set the servo upright so it is sitting on the heads of the 4 screws. Push down on the case and the screws will pop the top cap off. Notice the white bushing on the servo’s output shaft. That is what we will be replacing. If you don’t see it around the output, check the cap of the servo case.
servo-bearing-024

Bushing removed.
servo-bearing-027

A side by side shot of the bearing and bushing.
servo-bearing-028

Install the new bearing in the top cap.
servo-bearing-042

Reinstall the servo’s top cap and you are done!
servo-bearing-047

Performing this simple mod will add a lot of life to your AS-3 servo. As mentioned earlier, this is one of the best mods you can make to your RTR Axial vehicle for durability reasons. If you have an old AS-3 servo laying around because it has some slop and you wanted to upgrade. Try installing one of these bearings, and you will have a decent metal gear servo for your spare parts bin.

Link to 6x10x2.5 bearing.
http://www.fasteddybearings.com/6x10x2-5-metal-shielded-bearing-mr106zz-w2-5/

Still not sure you have the confidence to perform this modification? Check out Team Fast Eddy’s video tutorial for a visual step by step “how to”!

2013 Axial Geocache #3 – Florida!

axial_geocache

2013 Axial Geocache #3
Here’s the third Geocache of 2013! This one was hidden by our good friend Kha Ly down in central Florida. He came back from hiding this Geocache with stories of venomous spiders, a lost GPS unit, and something about a 15 foot gator?!

Remember, it’s about the adventure you create getting there to recover the goods that really make this program fun. We like to hear from you about your experience. You will not be disappointed with this location when you get there! Grab your R/C’s and head out to do some trail running. This is a cache and carry find, once you find it, it’s yours to take with you. Tread lightly and leave no trace.

Axial Geocache #3-2013 Coordinates:
Merritt Island National Wildlife Refuge http://www.fws.gov/merrittisland/

Latitude: 28.736598 Longitude: -80.753682 (If you don’t have a GPS unit paste the coordinates into Google maps and look for the green arrow)

What you get from us:
More prizes on top of the prize that you will find.

A few photo hints…..
1292955_681494638545764_400788354_o

1272577_681494798545748_2009544482_o

1277981_681494628545765_1376371348_o

1262652_681494705212424_435448262_o

1271423_681495105212384_1803651137_o

Full Option RTR SCX10 Jeep

blog_fulloption_jeep

Axial offers several optional upgrade parts for the Jeep Wrangler Unlimited Rubicon RTR and Kit. Here’s a quick run down of what is installed and why you may want to use these items.

A couple photos of the completed full option build. Axial offers complete body kits for the Jeep, part number AX04035, that includes the clear Lexan body and all the scale accessories. We also offer just the replacement clear Jeep bodies as well, part number AX04033.

First option we will cover is Axial’s simple LED kit, part number AX24257. The simple LED kit comes with 4 white and 2 red LED lights to keep you running long after the sun goes down. I used two small light buckets from Axial’s Light Bucket Set, part number AX80045, and attached them to the front bumper mount with long M3 screws. I used Axial’s LED lens set, part number AX80049, to cover the LEDs front and rear for a more realistic look. The lens kit includes both clear and yellow lens covers to give users a couple options. Need even more light? Add our NVS system, part number AX24251, for the ultimate scale light system.

A couple shots of the rear LEDs with the clear lens covers in place.

Next option added was our new fully licensed Icon shocks, part number AX30103. These come standard in the Jeep kit, but are an option part for the RTR. These shocks feature a new and improved CNC machined shock piston for smoother action through the range of travel. The new Icon shocks also feature clear coated polished aluminum bodies, complete with aluminum faux reservoirs. The main body of the shock is threaded for quick ride height adjustments and pre-load tuning ability. Like their full size counterparts these shocks are completely rebuildable, tunable and offer consistent handling all while adding some of that Icon bling to your SCX10™ chassis.

Axial’s aluminum link kit, part number AX30550, for the SCX10™ was the next upgrade we added. Upgrade your stock plastic links to high quality aluminum. Aluminum links have less flex than the stock plastic links which helps your vehicle track straighter in all conditions. This link kit includes aluminum suspension and steering links, as well as all hardware and rod ends required to complete the conversion.

A shot of the steering links. If you just want to upgrade your steering links only Axial offers a steering upgrade kit, part number AX30426, as well. Upgrading your steering links to aluminum with improve steering response in all conditions, especially in hard binds associated with rock crawling. Another option part that can be seen here is Axial’s HD 25t aluminum servo horn, part number AX30836. Axial’s HD aluminum servo horn provides more responsive steering with less chance of stripping the internal splines over the stock plastic servo horn. Clamping style head for secure mounting in high stress applications. Available in 23, 24 and 25 tooth spline counts.

In this photo you can see a handful of upgrades to improve steering performance and increase the strength of the front axle. Aluminum knuckles, part number AX30496, aluminum knuckles help your vehicle track more consistently in all situations. Combine our knuckles with our aluminum C-hubs, part number AX30495, for the ultimate steering precision. Another option part installed here is Axial’s CVD’s, part number AX30464, for the SCX10™ axles. The CVD’s provide more steering throw that the stock dog bone set-up which is great for tight, technical trail runs. CVD’s also have less slop than the stock set-up for increased efficiency.

Moving on to the rear axle we installed our aluminum axle lockouts, part number AX30494. Axial’s aluminum axle lockouts are more rigid than the stock plastic lockouts, which will allow the vehicle to track better in all situations.

Axial’s HD motor plate was our next upgrade, part number AX30860. Our heavy duty motor plate is for any vehicle running our AX10 transmission. CNC machined from 4.5mm thick billet aluminum, with integrated heatsink fins to help motors run cooler on those all day expeditions. A must have for any R/C overland adventurist! Axial also offers 13T, 14T and 15T steel pinion gears and an 80T spur gear to give end users an array of gear ratios to choose from. Add more torque for low speed crawling to your SCX10™ by installing Axial’s 55T motor. Or if more speed is your thing, add Axial’s 20T motor for higher top speeds. Another option part that we installed here is Axial’s dig system for the Wraith transmission, part number AX30793. This conversion also requires use of our Wraith Dig Transmission Case, part number AX80051. Axial’s dig system allows you to lock the rear wheels, while powering the front wheels only for a tighter turning radius. Shift servo sold separately.

Next option part installed is Axial’s black 1.9 beadlock wheels. Beadlock wheels allow users to tune foam set-ups and change tires at will for varying terrain and conditions. We also added our 1.9 internal weight rings, part number AX30547, for some added weight up front which will help us on steep vertical climbs. You can adjust how much weight is in the front wheels by using our 1.9 wheel weight inserts, part number AX30548.

For tires we went with our 1.9 Maxxis Trepador, part number AX12019. These tires are fully licensed by Maxxis and are molded in Axial’s sticky R35 compound for the ultimate traction in any conditions.

Complete SCX10™ option parts list:
AX8087 – 1.9 Black Eight Hole Beadlock Wheels (x3 to have spare tire)
AX8088 – 1.9 Chrome Eight Hole Beadlock Wheel (x3 to have spare tire)
AX08138 – 1.9 Black Walker Evans Wheels (x3 to have spare tire)
AX12019 – 1.9 Maxxis Trepador Tires R35 Compound (x3 to have spare tire)
AX12016 – 1.9 Ripsaw Tire R35 Compound (x3 to have spare tire)
AX30547 – 1.9 Internal Weight Rings (x2)
AX30548 – 1.9 Wheel Weight Inserts (x3)
AX30549 – SCX10™ Aluminum Link Set (11.4″ wheelbase – Dingo)
AX30550 – SCX10™ Aluminum Link Set (12.3″ wheelbase – Honcho and Jeep)
AX30426 – SCX10™ Aluminum Steering Kit
AX30464 – SCX10™ Universal Axle Set
AX30395 – HD Ring and Pinion Gear Sets (stock gear ratio) (x2)
AX30401 – Overdrive HD Ring and Pinion Gear Sets (x2)
AX30402 – Underdrive HD Ring and Pinion Gear Sets (x2)
AX30786 – Aluminum WB8 Driveshaft Retainer Rings (x2)
AX30571 – 13t Steel Pinion Gear
AX30569 – 14t Steel Pinion Gear
AX30573 – 15t Steel Pinion Gear
AX30665 – 80t Spur Gear
AX30860 – HD Motor Plate
AX30834 – 23t HD Servo Horn
AX30835 – 24t HD Servo Horn
AX30836 – 25t HD Servo Horn
AX30494 – Aluminum Axle Lockouts
AX30495 – Aluminum Axle C-hub’s
AX30496 – Aluminum Knuckles
AX30103 – Icon Aluminum Shocks (x2)
AX30132 – Machined Shock Piston 7mm – 1.5×3 (4pcs)
AX24260 – AE-3 Vanguard ESC
AX24010 – Vanguard 2900KV Brushless Motor
AX24007 – 55 Turn Motor
AX24003 – 20 Turn Motor
AX24256 – 5 LED Light String
AX24257 – Simple LED Kit
AX24251 – NVS Light System
AX80045 – Light Bucket Set (x2)
AX80049 – LED Lens Set – Yellow / Clear (4pcs)
AX30793 – Dig Component Set
AX80051 – Dig Transmission Case
AX04033 – Clear Jeep Wrangler Unlimited Rubicon Body (Body only)
AX04035 – Complete Jeep Wrangler Unlimited Rubicon Body Kit
AX30200 – Red Springs 3.6 lbs/in (short) (x2)
AX30201 – White Springs 4.32 lbs/in (short) (x2)
AX30202 – Green Springs 5.44 lbs/in (short) (x2)
AX30203 – Yellow Springs 6.53 lbs/in (short) (x2)
AX30204 – Blue Springs 7.95 lbs/in (short) (x2)
AX30205 – Red Springs 2.7 lbs/in (long) (x2)
AX30206 – White Springs 3.6 lbs/in (long) (x2)
AX30207 – Green Springs 4.08 lbs/in (long) (x2)
AX30208 – Yellow Springs 5.44 lbs/in (long) (x2)
AX30209 – Blue Springs 6.81 lbs/in (long) (x2)

Full Option RTR Poison Spyder Wraith

Axial offers several optional upgrade parts for the Poison Spyder Wraith RTR. Here’s a quick run down of what is installed and why you may want to use these items.

A couple shots of the fully optioned Poison Spyder Wraith RTR in the studio.

In this shot you can see you can see a handful of upgrades. The first upgrade is aluminum shocks, part number AX30092. Aluminum shocks provide better dampening than the stock plastic shocks, especially when mated with our polyoxymethylene – (POM/thermoplastic) shock pistons. The aluminum shock body and cap have less flex than plastic versions. Aluminum shock bodies also dissipate heat better than the stock plastic bodies. The shock shafts are oversized (3.5mm) for rigidity. They’re great for high power applications and long run times! We also offer a complete line of various springs to fine tune your suspension as needed – see the complete parts list below for more info.

Another parts upgrade is the front sway bar, part number AX30781. Designed for high speed this system will let you soften up your suspension for jumps, while keeping torque twist and body lean to a minimum during acceleration. A sway bar’s main function is to control body roll, yet still allow your shocks to move vertically with the changing terrain. What does all this mean? It means more stability at high speed. A must have upgrade for any would-be rock racer. Installing sway bars does limit articulation, so this is an option best suited for high speed applications. Great for use with our Vanguard brushless system, part number AX24010 and AX24260.

Moving on to the next part we installed a 25T aluminum servo horn, part number AX30836. Axial’s HD aluminum servo horn provides more responsive steering with less chance of stripping the internal splines over the stock plastic servo horn. Clamping style head for secure mounting in high stress applications. Available in 23, 24 and 25 tooth spline counts.

Axial’s next option part install is the Universal Light Bar, part number AX30709. Axial’s light bar is a great way to add realism and working lights to your Wraith with this universal light bar. Another option part that we plan to install is Axial’s NVS Light System, part number AX24251. The ultimate level in detail you can now add the NVS light system which features controls for headlights, tail lights, brake lights, and right / left turn signals, as well as some extra auxiliary lighting. Great for those night time expeditions. We also offer a 5 string LED light set, part number AX24256, to fit this light bar and it is compatible with Axial’s simple LED kit, part number AX24257, and our NVS System.

Another great upgrade is the Wraith Stage One link kit, part number AX30797. Add even more durability to your Wraith by upgrading your stock plastic RTR suspension links with our HD Stage 1 Aluminum Link Kit. Replaces all the stock plastic suspension links with high quality 7mm diameter aluminum links. These links eliminate axle wrap and unwanted axle steer, especially in high power applications. Axial also offers machined heavy duty aluminum straight links, part number AX30790, to replace the stock plastic lower links as an alternative the the Stage One link kit.

Axial’s HD motor plate, part number AX30860. Our heavy duty motor plate is for any vehicle running our AX10 transmission. CNC machined from 4.5mm thick billet aluminum, with integrated heatsink fins to help motors run cooler on those all day expeditions. A must have for any R/C overland adventurist! Axial also offers 13T, 14T and 15T steel pinion gears and an 87T spur gear to give end users an array of gear ratios to choose from. Add more torque for low speed crawling to your Wraith by installing one of Axial’s optional brushed motors available in 27T and 55T configurations. Another option part that we installed here is Axial’s dig system for the Wraith transmission, part number AX30793. Axial’s dig system allows you to lock the rear wheels, while powering the front wheels only for a tighter turning radius. Shift servo sold separately.

Axial’s HD differential covers, part number AX30829. HD diff covers protect ring and pinion gears from being damaged by rocks, just like their 1:1 counterparts, all while adding a little bling to your ride.

Another option part that is usually hiding behind the HD cover is Axial’s HD ring and pinion gears, part number AX30395. HD ring and pinion gears are more efficient than the stock aluminum ring and pinions. CNC machined for precision, hardened steel for durability – great for high power applications. Axial also offers hardened steel overdrive ring and pinion gear sets, part number AX30401, for a little extra wheel speed. We also offer an underdrive ring and pinion gear set, part number AX30402, for a little more torque in binds.

Axial’s HD lower link mounts are another noteworthy upgrade, part number AX30830. Our HD lower link mounts allow users to fine tune ride height and wheelbase by providing more adjustment holes than the stock plastic units.

This shot also shows a few options parts. First option is aluminum knuckles, part number AX30760. Aluminum knuckles provide more responsive steering and helps vehicle track better at speeds and in the rocks. Another option shown is the Axial Aluminum C-hubs, part number AX30762. Aluminum C-hubs also help your vehicle track more consistently in all situations, especailly when used in conjunction with our aluminum knuckles. Also notice the AR60 universal axles, part number AX30780. Axial universal joint axles increase steering angle to 50 degrees, that’s 60% over the stock dogbone/drive cup setup. These universals provide smoother action for a higher performing, efficient drivetrain. The universal is oversized; typical for 1/8 scale vehicles and made of hardened steel so it’s capable of handling extreme power.

Next option is the rear sway bar, part number AX30782. Designed for high speed this system will let you soften up your suspension for jumps, while keeping torque twist and body lean to a minimum during acceleration. A sway bar’s main function is to control body roll, yet still allow your shocks to move vertically with the changing terrain. What does all this mean? It means more stability at high speed. A must have upgrade for any would be rock racer. Installing sway bars does limit articulation, so this is an option best suited for high speed applications. Great for use with our Vanguard brushless system, part number AX24010 and AX24260.

Aluminum axle lockouts are another great upgrade, part number AX30789. Axial’s aluminum axle lockouts are more rigid than the stock plastic lockouts, which will allow the vehicle to track better in all situations.

We left the wheels and tires stock on this build. But, if you are looking to upgrade your wheels, we suggest our VWS beadlocks, part number AX08061. VWS wheels allow users to tune foam set-ups and change tires at will for varying terrain and conditions. Another wheel option offered by Axial is our black 8 hole beadlock wheels, part number AX8097. These wheels offer a little wider overall stance which equals stability at high speeds. For low speed rock crawling you can increase your Wraith’s climbing abilities by adding Axial’s 2.2 Internal Weight Rings, part number AX30545. Add even more weight by utilizing Axial’s 2.2 Internal Wheel Weights for the Internal Wheel Weight Rings, part number AX30546.

You can see our R35 Ripsaw tires pictured here on the full option RTR Wraith, part number AX12015. R35 Ripsaw tires offer both a realistic look for the image-conscious scale crawler and for those looking to up their performance game. This 2.2 Ripsaw offers an aggressive tread design, greater ground clearance, and is made from a R35 sticky compound. The VWS wheels include black aluminum rings, but I swapped those out for our Grey beadlock rings, part number AX08133, just to match the grey colored suspension links.

Complete Poison Spyder Wraith option parts list:
AX8097 – 2.2 Black 8 Hole Beadlock Wheels (x2)
AX08061 – 2.2 VWS Beadlock Wheels (x2)
AX08133 – Grey VWS Beadlock Rings (x2)
AX12015 – 2.2 R35 Ripsaw Tires (x2)
AX30545 – 2.2 Internal Wheel Weight Rings (x2)
AX30546 – 2.2 Wheel Weight Inserts (x2)
AX30797 – Stage One Link Kit
AX30790 – Machined Heavy Duty Aluminum Straight Link 101mm (x2)
AX30469 – Machined Heavy Duty Aluminum High Clearance Upper Links (x2)
AX80057 – XR10 Linkage Set (x4 for all 8 links)
AX30395 – HD Ring and Pinion Gear Sets (x2)
AX30401 – Overdrive HD Ring and Pinion Gear Sets (x2)
AX30402 – Underdrive HD Ring and Pinion Gear Sets (x2)
AX30571 – 13t Steel Pinion Gear
AX30569 – 14t Steel Pinion Gear
AX30573 – 15t Steel Pinion Gear
AX30672 – 87t Spur Gear
AX30829 – HD Differential Covers (x2)
AX30860 – HD Motor Plate
AX30830 – HD Link Mounts (x2)
AX30834 – 23t HD Servo Horn
AX30835 – 24t HD Servo Horn
AX30836 – 25t HD Servo Horn
AX30762 – Aluminum Axle C-hub’s
AX30760 – Aluminum Knuckles
AX30789 – Aluminum Axle Lockouts
AX30092 – Aluminum Shocks (x2)
AX30780 – AR60 Universal Axle Set
AX30781 – Front Sway Bar
AX30782 – Rear Sway Bar
AX30709 – Universal Light Bar
AX24256 – 5 LED Light String
AX24257 – Simple LED Kit
AX24251 – NVS Light System
AX24010 – Vanguard Brushless Motor
AX24260 – AE-3 Vanguard ESC
AX24007 – 55 Turn Motor
AX24004 – 27 Turn Motor
AX30793 – Dig Component Set
AX04027 – Wraith Clear Body Panel Kit
AX30223 – Black Springs 1.04 lbs/in (x2)
AX30224 – Purple Springs 1.43 lbs/in (x2)
AX30225 – Orange Springs 1.75 lbs/in (x2)
AX30218 – Red Springs 2.07 lbs/in (x2)
AX30219 – White Springs 2.47 lbs/in (x2)
AX30220 – Green Springs 2.85 lbs/in (x2)
AX30221 – Yellow Springs 3.27 lbs/in (x2)
AX30222 – Blue Springs 3.55 lbs/in (x2)

Full Option RTR Wraith

Axial offers several optional upgrade parts for the Wraith RTR and Kit. Here’s a quick run down of what is installed and why you may want to use these items.

A shot of the completed Wraith in the studio, Axial offers clear body panels for the Wraith, part number AX04027, to give your rock racer a custom look.

In this shot you can see a handful of upgrades. The first upgrade is aluminum shocks, part number AX30092. Aluminum shocks provide better dampening than the stock plastic shocks, especially when mated with our polyoxymethylene  – (POM/thermoplastic) shock pistons. The aluminum shock body and cap have less flex than plastic versions. Aluminum shock bodies also dissipate heat better than the stock plastic bodies. The shock shafts are oversized (3.5mm) for rigidity. They’re great for high power applications and long run times! We also offer a complete line of various springs to fine tune your suspension as needed – see the complete parts list below for more info.

Another parts upgrade is the front sway bar, part number AX30781. Designed for high speed this system will let you soften up your suspension for jumps, while keeping torque twist and body lean to a minimum during acceleration. A sway bar’s main function is to control body roll, yet still allow your shocks to move vertically with the changing terrain. What does all this mean? It means more stability at high speed. A must have upgrade for any would-be rock racer. Installing sway bars does limit articulation, so this is an option best suited for high speed applications. Great for use with our Vanguard brushless system, part number AX24010 and AX24260.

Moving on to the next part we installed a 25T aluminum servo horn, part number AX30836. Axial’s HD aluminum servo horn provides more responsive steering with less chance of stripping the internal splines over the stock plastic servo horn. Clamping style head for secure mounting in high stress applications. Available in 23, 24 and 25 tooth spline counts.

Axial’s next option part install is the Universal Light Bar, part number AX30709. Axial’s light bar is a great way to add realism and working lights to your Wraith with this universal light bar. Another option part that we plan to install is Axial’s NVS Light System, part number AX24251. The ultimate level in detail you can now add the NVS light system which features controls for headlights, tail lights, brake lights, and right / left turn signals, as well as some extra auxiliary lighting. Great for those night time expeditions. We also offer a 5 string LED light set, part number AX24256, to fit this light bar and it is compatible with Axial’s simple LED kit, part number AX24257, and our NVS System.

Another great upgrade is the Wraith Stage One link kit, part number AX30797. Add even more durability to your Wraith by upgrading your stock plastic RTR suspension links with our HD Stage 1 Aluminum Link Kit. Replaces all the stock plastic suspension links with high quality 7mm diameter aluminum links. These links eliminate axle wrap and unwanted axle steer, especially in high power applications. Axial also offers machined heavy duty aluminum straight links, part number AX30790, to replace the stock plastic lower links as an alternative the the Stage One link kit.

Axial’s HD motor plate, part number AX30860. Our heavy duty motor plate is for any vehicle running our AX10 transmission. CNC machined from 4.5mm thick billet aluminum, with integrated heatsink fins to help motors run cooler on those all day expeditions. A must have for any R/C overland adventurist! Axial also offers 13T, 14T and 15T steel pinion gears and an 87T spur gear to give end users an array of gear ratios to choose from. Add more torque for low speed crawling to your Wraith by installing one of Axial’s optional brushed motors available in 27T and 55T configurations. Another option part that we installed here is Axial’s dig system for the Wraith transmission, part number AX30793. Axial’s dig system allows you to lock the rear wheels, while powering the front wheels only for a tighter turning radius. Shift servo sold separately.

Axial’s HD differential covers, part number AX30829. HD diff covers protect ring and pinion gears from being damaged by rocks, just like their 1:1 counterparts, all while adding a little bling to your ride.

Another option part that is usually hiding behind the HD cover is Axial’s HD ring and pinion gears, part number AX30395. HD ring and pinion gears are more efficient than the stock aluminum ring and pinions. CNC machined for precision, hardened steel for durability – great for high power applications. Axial also offers hardened steel overdrive ring and pinion gear sets, part number AX30401, for a little extra wheel speed. We also offer an underdrive ring and pinion gear set, part number AX30402, for a little more torque in binds.

Axial’s HD lower link mounts are another noteworthy upgrade, part number AX30830. Our HD lower link mounts allow users to fine tune ride height and wheelbase by providing more adjustment holes than the stock plastic units.

This shot also shows a few options parts. First option is aluminum knuckles, part number AX30760. Aluminum knuckles provide more responsive steering and helps vehicle track better at speeds and in the rocks. Another option shown is the Axial Aluminum C-hubs, part number AX30762. Aluminum C-hubs also help your vehicle track more consistently in all situations, especailly when used in conjunction with our aluminum knuckles. Also notice the AR60 universal axles, part number AX30780. Axial universal joint axles increase steering angle to 50 degrees, that’s 60% over the stock dogbone/drive cup setup. These universals provide smoother action for a higher performing, efficient drivetrain. The universal is oversized; typical for 1/8 scale vehicles and made of hardened steel so it’s capable of handling extreme power.

Next option is the rear sway bar, part number AX30782. Designed for high speed this system will let you soften up your suspension for jumps, while keeping torque twist and body lean to a minimum during acceleration. A sway bar’s main function is to control body roll, yet still allow your shocks to move vertically with the changing terrain. What does all this mean? It means more stability at high speed. A must have upgrade for any would be rock racer. Installing sway bars does limit articulation, so this is an option best suited for high speed applications. Great for use with our Vanguard brushless system, part number AX24010 and AX24260.

Aluminum axle lockouts are another great upgrade, part number AX30789. Axial’s aluminum axle lockouts are more rigid than the stock plastic lockouts, which will allow the vehicle to track better in all situations.

For wheels, we went with our VWS beadlocks, part number AX08061. VWS wheels allow users to tune foam set-ups and change tires at will for varying terrain and conditions. Another wheel option offered by Axial is our black 8 hole beadlock wheels, part number AX8097. These wheels offer a little wider overall stance which equals stability at high speeds. For low speed rock crawling you can increase your Wraith’s climbing abilities by adding Axial’s 2.2 Internal Weight Rings, part number AX30545. Add even more weight by utilizing Axial’s 2.2 Internal Wheel Weights for the Internal Wheel Weight Rings, part number AX30546.

You can see our R35 Ripsaw tires pictured here, part number AX12015. R35 Ripsaw tires offer both a realistic look for the image-conscious scale crawler and for those looking to up their performance game. This 2.2 Ripsaw offers an aggressive tread design, greater ground clearance, and is made from a R35 sticky compound. The VWS wheels include black aluminum rings, but I swapped those out for our Grey beadlock rings, part number AX08133, just to match the grey colored suspension links.

Complete Wraith option parts list:
AX8097 – 2.2 Black 8 Hole Beadlock Wheels (x2)
AX08061 – 2.2 VWS Beadlock Wheels (x2)
AX08133 – Grey VWS Beadlock Rings (x2)
AX12015 – 2.2 R35 Ripsaw Tires (x2)
AX30545 – 2.2 Internal Wheel Weight Rings (x2)
AX30546 – 2.2 Wheel Weight Inserts (x2)
AX30797 – Stage One Link Kit
AX30790 – Machined Heavy Duty Aluminum Straight Link 101mm (x2)
AX30469 – Machined Heavy Duty Aluminum High Clearance Upper Links (x2)
AX80057 – XR10 Linkage Set (x4 for all 8 links)
AX30395 – HD Ring and Pinion Gear Sets (x2)
AX30401 – Overdrive HD Ring and Pinion Gear Sets (x2)
AX30402 – Underdrive HD Ring and Pinion Gear Sets (x2)
AX30571 – 13t Steel Pinion Gear
AX30569 – 14t Steel Pinion Gear
AX30573 – 15t Steel Pinion Gear
AX30672 – 87t Spur Gear
AX30829 – HD Differential Covers (x2)
AX30860 – HD Motor Plate
AX30830 – HD Link Mounts (x2)
AX30834 – 23t HD Servo Horn
AX30835 – 24t HD Servo Horn
AX30836 – 25t HD Servo Horn
AX30762 – Aluminum Axle C-hub’s
AX30760 – Aluminum Knuckles
AX30789 – Aluminum Axle Lockouts
AX30092 – Aluminum Shocks (x2)
AX30780 – AR60 Universal Axle Set
AX30781 – Front Sway Bar
AX30782 – Rear Sway Bar
AX30709 – Universal Light Bar
AX24256 – 5 LED Light String
AX24257 – Simple LED Kit
AX24251 – NVS Light System
AX24010 – Vanguard Brushless Motor
AX24260 – AE-3 Vanguard ESC
AX24007 – 55 Turn Motor
AX24004 – 27 Turn Motor
AX30793 – Dig Component Set
AX04027 – Wraith Clear Body Panel Kit
AX30223 – Black Springs 1.04 lbs/in (x2)
AX30224 – Purple Springs 1.43 lbs/in (x2)
AX30225 – Orange Springs 1.75 lbs/in (x2)
AX30218 – Red Springs 2.07 lbs/in (x2)
AX30219 – White Springs 2.47 lbs/in (x2)
AX30220 – Green Springs 2.85 lbs/in (x2)
AX30221 – Yellow Springs 3.27 lbs/in (x2)
AX30222 – Blue Springs 3.55 lbs/in (x2)

A Years Worth of Abuse in One Week?

Those of you that attended the 2012 King of the Hammers race may have seen the Axial demo booth that was set-up near the pit area. Axial ran a demo during the week of KOH with some of our new 2012 SCX10 Jeep Wrangler Unlimited Rubicon RTR’s. This demo allowed anyone attending the King of the Hammers event to try their hand at driving one of our scale Jeeps on the obstacle course that was built on site. The demo ran twice a day for 2 hours at a time for 5 days, so there is 20 hours of drive time right off the bat. There was also a few extra credit runs at night with these trucks, so we will add another 10 hours of run time there to be on the safe side. We are now at about 30 hours of solid run time for the week, for each of these demos. We recently went to take a look at the condition of the the demo Jeeps in order to prep them for another Axial demo for the 2013 Easter Jeep Safari in Moab, Utah. We grab the first demo JK, pulled it out of the box and was amazed to see how much wear and tear these rigs went through during their week at KOH. The demo rigs look like they had been used for a year, not a week. Everything was intact and working on all the demo SCX10′s too. I thought we put a lot of abuse on the SCX10-JK in the 3 days we spent on the Rubicon. But, the demo drivers at KOH have us beat by a mile as far as the abuse they inflicted upon these demo SCX10′s. Impressive!!

A few photos of the wear and tear. Starting with the front bumper and d-rings.

The front axle.

Chassis skid plate and lower links.

Front driveshaft.

Front wheels. It’s hard to see but almost all the chrome is missing from the outer lip of the wheel.

Moving on to the body, the mirrors took on a bunch of rock rash, but are still intact.

Same goes for the Poison Spyder licensed Crusher Flares, lots of rock rash but they protected the body just like the real product is designed to do.

Rear Crusher Flares.

Again some impressive rock rash for only a few days of running. Way to do work KOH demo drivers!!

Battery Relocation – SCX10 Jeep RTR

We have been getting a few requests recently for a “step by step” tutorial on relocating the battery from its stock location in the rear on the SCX10-JK, to the front. This is a simple modification that can really transform how your rig performs in the rocks. Moving weight from the back to the front of a vehicle greatly enhances its ability to climb steep rock faces. This is a no brainer for me, as I am all about performance with my rigs regardless if they are scale or comp rigs. So let’s dig in!

I am using a “kit” SCX10-JK for this article, but the steps are exactly the same for the kit and RTR Jeeps. A couple shots of the battery tray in stock RTR form.

First thing we need to do is remove the two screws holding the metal battery tray to the chassis.

With the metal tray removed you can access the screws that hold the plastic base of the battery tray.

Remove the two screws that hold the base of the battery tray to the chassis cross-member, located between the rear shock towers.

Next remove the two screws that tie the radio box to the front chassis cross-member.

Locate the bag of plastic extras that is included with the RTR Jeep. Inside there are a few parts required to complete this modification.

Find two of the three battery tray posts in your bag of extras. These will be the main supports for the tray in its new location.

Now grab the parts tree numbered AX80009 from your bag of extras. Cut item #5 off the parts tree. We will use this spacer for the front of the battery tray.

The hardware required for the relocation.

The two main support screws should measure just over an inch.

The front screw needs to be shorter and should measure in the 5/8″ range.

Insert the two long screws in the holes closest to center of the plastic battery tray base, then slide the plastic battery tray posts over the screws.

While holding the spacers on the screws, set the battery base into place so the two long screws line up with the radio box holes. Tighten the screws down until they are snug.

Now grab your short front spacer and set it into place over the front frame cross-member’s molded boss.

Set the metal battery tray into place on the plastic base and install the shorter 5/8″ long screw through the front of the whole assembly.

Install the short flathead screw that holds the metal tray to the plastic base at the rear.

And you are done! A shot of the newly relocated battery tray.

Following these simple steps to move the battery will greatly improve on your SCX10′s already amazing capabilities. Time to go hit the trails!!