Axial Yeti / RR10 Transmission Parts List

Axial Yeti / RR10 Bomber Tranmission Break Down

Found in: YETI SCORE TROPHY TRUCK / YETI / RR10 BOMBER

Stock Gearing
Yeti: 32P 16T Pinion / 64T Spur Gear
Yeti SCORE Trophy Truck: 32P 16T Pinion / 64T Spur Gear
RR10 Bomber: 32P 12T Pinion / 64T Spur Gear

Axial Transmission Guide - RR10 BomberTransmission

Gearing Chart

32 Pitch (Stock Gearing AX30392 or AX30395)

_
Spur Gear

Pinion
56
60
64
68
11
28.85
30.91
32.97
35.03
12
26.44
28.33
30.22
32.11
13
24.41
26.15
27.90
29.64
14
22.67
24.28
25.90
27.52
15
21.15
22.67
24.18
25.69
16
19.83
21.25
22.67
24.08
17
18.67
20.00
21.33
22.67

32 Pitch (Overdrive Gearing AX30401)

_
Spur Gear

Pinion
56
60
64
68
11
25.38
27.19
29.00
30.81
12
23.26
24.92
26.58
28.25
13
21.47
23.01
24.54
26.07
14
19.94
21.36
22.79
24.21
15
18.61
19.94
21.27
22.60
16
17.45
18.69
19.94
21.18
17
16.42
17.59
18.77
19.94

32 Pitch (Underdrive Gearing AX30402)

_
Spur Gear

Pinion
56
60
64
68
11
25.38
34.97
37.31
39.64
12
29.92
32.06
34.20
36.33
13
27.62
29.59
31.57
33.54
14
25.65
27.48
29.31
31.14
15
23.94
25.65
27.36
29.07
16
22.44
24.04
25.65
27.25
17
21.12
22.63
24.14
25.65

divider

divider

AXIAL YETI SCORE TROPHY TRUCK / YETI / RR10 BOMBER

AXA0413 M2.6x8mm Hex Screws
AXA1045 M4 Nylon Locking Hex Nuts
AXA1221 Bearing 5x11x4mm
AXA1391 E4 E-clips
AXA144 M3x8mm Flat Head Screws
AXA0147 M3x16mm Flat Head Screws
AXA148 M3x18mm Flat Head Screws
AXA150 M3x25mm Flat Head Screws
AX30163 Pin 2.0x10mm
AX30413 Slipper Spring
AX31059 Slipper Plate Washer
AX31065 Spur Gear 23P 64T
AX31067 Slipper Plate
AX31068 Slipper Pads
AX31106 2-Speed Hi/Lo Transmission Motor Mount
AX31107 2-Speed Hi/Lo Transmission Spur Gear Cover
AX31108 2-Speed Hi/Lo Transmission Case
AX31127 2-Speed Hi/Lo Transmission Top Shaft
AX31129 2-Speed Hi/Lo Transmission Bottom Shaft
AX31130 High Speed Transmission Gear Set
AX31131 T-Case Gear Set
AX31180 Aluminum Spur Gear Spacer
AX31313 Transfer Case Output Shaft
AX31324 RR10 Transfer Case

Axial AX10™ Transmission Parts List

Axial AX10 Tranmission Break Down

A quick reference parts list for the Axial AX10™ Transmission.

Found in: AX10 / SCX10 / SCX10 II RTR / WRAITH / SMT10 3 GEAR TRANS

Stock Gearing
SCX10: 32P 13T Pinion / 56T Spur Gear
SCX10 II RTR: 32P 13T Pinion / 56T Spur Gear
Wraith: 32P 12T Pinion / 56T Spur Gear
SMT10: 32P 16T Pinion / 56T Spur Gear

Axial Transmission Guide - AX10 Transmission

Gearing Chart

32 Pitch (Stock Gearing AX30392 or AX30395)

_
Spur Gear

Pinion
56
60
64
68
11
38.69
41.45
44.22
46.98
12
35.47
38.00
40.53
43.07
13
32.74
35.08
37.42
39.75
14
30.40
32.57
34.74
36.91
15
28.37
30.40
32.43
34.45
16
26.60
28.50
30.40
32.30
17
25.04
26.82
28.61
30.40

32 Pitch (Overdrive Gearing AX30401)

_
Spur Gear

Pinion
56
60
64
68
11
34.04
36.47
38.90
41.33
12
31.20
33.43
35.66
37.89
13
28.80
30.86
32.91
34.97
14
26.74
28.65
30.56
32.47
15
24.96
26.74
28.53
30.31
16
23.40
25.07
26.74
28.41
17
22.02
23.60
25.17
26.74

32 Pitch (Underdrive Gearing AX30402)

_
Spur Gear

Pinion
56
60
64
68
11
43.78
46.91
50.04
53.16
12
40.13
43.00
45.87
48.73
13
37.05
39.69
42.34
44.98
14
34.40
36.86
39.31
41.77
15
32.11
34.40
36.69
38.99
16
30.10
32.25
34.40
36.55
17
28.33
30.35
32.38
34.40

divider

AXIAL AX10™ TRANSMISSION PARTS LIST

AX30487 Complete AX10 Transmission
AXA013 M2x6mm SH Screws
AXA089 M3x25mm SC Screws
AXA1045 M4 Nylon Lock Nuts
AXA1053 M3 Nylon Locking Hex Nuts
AXA1218 Bearing, 5x10x4mm (2 pkgs)
AXA1225 Bearing, 8x16x5mm
AX30162 Cross Pin
AX30190 Shaft 5x18mm
AX30394 20T Drive Gear
AX30413 Slipper Spring
AX30435 Steel Outdrive Set
AX30491 AX10 RTR Motor Plate
AX31026 Slipper Plate Washer
AX31027 Spur Gear 32P 56T
AX31068 Slipper Pad
AX31149 Slipper Drive Gear Shaft
AX80009 Transmission Set
AX80010 Gear Set
AX80078 Transmission Spur Gear Cover

Supercrawl 2017 – Lasernut Racing

Supercrawl 2017 - Lasernut Racing

The Lasernut Racing crew was out at the Supercrawl 2017 event held at Wild West Motorsports Park in Sparks, NV. Our very own Randall Davis, spotter for Lasernut team driver Cody Waggoner, was part of the winning team that took place on September 23-24, 2017.

Not only was this the first event that Cody had a chance to drive the car, it was also the first they had ever SEEN it! The new moon buggy was aptly named Pretty Penny – just check out those stunning copper wheels!

At the end of the comp on day one there was only a 1 point separation between 1st, 2nd, 3rd. Lasernut was sitting in first but knew that one mistake would cost them to lose the position. The Lasernut crew had a near perfect final day, making a flawless run on the final course to seal the championship!!

Links
https://www.facebook.com/Supercrawl2017/
http://supercrawl.rocks/
http://supercrawl.rocks/results/2017-results/

Below are pictures from the event as well as the runs from both days 1 and 2.

Video – Day 1

Video – Day 2

Pictures
IMG_2667

IMG_2668

IMG_2670

IMG_2671

IMG_2673

IMG_2675

IMG_2677

IMG_2685

IMG_2686

IMG_2687

IMG_2692

IMG_2695

IMG_2697

IMG_2699

IMG_2701

IMG_2702

IMG_2704

IMG_2705

IMG_2707

IMG_2711

IMG_2714

IMG_2715

IMG_2718

IMG_2719

IMG_2722

IMG_2723

IMG_2724

IMG_2727

IMG_2730

IMG_2746

IMG_2747

IMG_2749

IMG_2751

IMG_2753

IMG_2755

IMG_2756

IMG_2761

IMG_2762

IMG_2763

IMG_2768

IMG_2773

IMG_2774

IMG_2776

IMG_2777

IMG_2779

IMG_2780

IMG_2782

IMG_2783

IMG_2784

IMG_2785

IMG_2787

IMG_2788

IMG_2789

IMG_2790

IMG_2791

IMG_2793

IMG_2795

IMG_2799

IMG_2806

IMG_2807

IMG_2808

IMG_2809

IMG_2810

IMG_2811

IMG_2814

Lucas Oil Offroad EXPO 2017

Lucas Oil Offroad EXPO 2017

This years Lucas Oil Off-Road Expo was once again held at the world famous Pomona Fairplex in Pomona, CA. In addition to having the greatest collection of off-road companies, parts, equipment, gear, action and experts ever assembled in America, there were also thousands of people cruising through to see some amazing vehicles!

Fans had a chance to experience the dynamic world of off-road thru ride-alongs, racing demos, celebrity appearances, live music, industry media events and product giveaways all weekend long.

As you can see from the photos below, we had a great time checking out all the equipment! We’ll be sure to be there again next year!

IMG_5536

IMG_5537

IMG_5538

IMG_5539

IMG_5540

IMG_5544

IMG_5547

IMG_5548

IMG_5549

IMG_5550

IMG_5552

IMG_5554

IMG_5556

IMG_5557

IMG_5558

IMG_5560

IMG_5562

IMG_5563

IMG_5564

IMG_5566

IMG_5568

IMG_5570

IMG_5571

IMG_5572

IMG_5573

IMG_5574

IMG_5575

IMG_5576

IMG_5577

IMG_5578

IMG_5579

IMG_5580

IMG_5581

IMG_5582

IMG_5583

IMG_5584

IMG_5587

IMG_5588

IMG_5590

IMG_5592

IMG_5593

IMG_5595

IMG_5597

IMG_5599

IMG_5601

IMG_5602

IMG_5604

IMG_5605

IMG_5606

IMG_5607

IMG_5608

IMG_5609

IMG_5610

IMG_5612

IMG_5613

IMG_5615

IMG_5617

IMG_5619

IMG_5622

IMG_5623

IMG_5625

IMG_5626

IMG_5628

IMG_5632

IMG_5633

IMG_5634

IMG_5636

IMG_5638

IMG_5639

IMG_5641

IMG_5643

IMG_5645

IMG_5647

IMG_5648

IMG_5649

IMG_5651

IMG_5653

IMG_5654

IMG_5655

IMG_5656

IMG_5657

IMG_5658

IMG_5659

IMG_5661 1

IMG_5661

IMG_5662

IMG_5663

IMG_5664

IMG_5665

IMG_5666

IMG_5667

IMG_5668

IMG_5669

IMG_5670

IMG_5671

IMG_5672

IMG_5673

IMG_5676

IMG_5677

IMG_5678

IMG_5679

IMG_5680

IMG_5681

IMG_5682

IMG_5683

IMG_5684

IMG_5688

IMG_5689

IMG_5690

IMG_5692

IMG_5693

IMG_5694

IMG_5695

IMG_5696

IMG_5697

IMG_5698

IMG_5699

IMG_5700

IMG_5702

IMG_5703

IMG_5704

IMG_5706

IMG_5708

IMG_5709

AXIALFEST2017 Concourse Results

AXIALFEST2017 Concourse Results

The Concourse event at this year’s AXIALFEST2017 was absolutely amazing! The builders are getting so much more creative than previous years that it’s making it near impossible to pick a winner.

In the end, though, the judges did have to crown the best of the best, so here’s the pictures of the winner’s rigs. We’ve also added a small gallery at the bottom with some additional pictures.

AXIALFEST2017 Concourse WinnersBest of Axial Heritage Winner: Patrick Jurica


AXIALFEST2017 Concourse WinnersBest of Adventure Trailer Winner: Matt Alley


AXIALFEST2017 Concourse WinnersBest of Work Trailer Winner: Chris Zemek


AXIALFEST2017 Concourse WinnersBest of Adventurist Winner: Dan Huff


AXIALFEST2017 Concourse WinnersBest of Monster Truck Winner: Jim Prestwood


AXIALFEST2017 Concourse WinnersBest of Daily Driver Winner: Troy Olsen


AXIALFEST2017 Concourse WinnersBest of D’Raison Winner: Jackson Hall


AXIALFEST2017 Concourse WinnersBest of Trophy Truck Winner: Jason Philo (right)


AXIALFEST2017 Concourse Winners

AXIALFEST2017 Concourse Winners
BEST OF SHOW Winner: Todd Pearson


Additional Pix

Product Spotlight: AX31150 Axial Clear Inner Fenders

AX31150 Axial Inner Fenders

While prepping my truck for this years #AXIALFEST2017 (ok, my wife’s truck), I happened to notice one of my fellow co-workers bolting on a set of inner fenders onto his SCX10 II XJ. I asked him where he got those and he informed me it was an actual Axial product, just maybe one that wasn’t so well known.

Of course, I had to investigate further – AX31150 is in fact a molded piece of .40″ clear Lexan that not only includes 4 inner fenders, it also has floor panels for trucks that don’t have them (the SCX10 for example). In addition to giving you extra space to mount electronics, it also acts as a barrier to help keep mud, water and other debris from entering the chassis.

Product Spotlight: AX31150 Axial Clear Inner Fenders

As you can see, it comes clear and can be painted any color you want (I’m going with from-the-factory black). A strip of double-sided tape is included to securely attach them to the side rails. Another cool thing is that they are a universal fit; you can trim them to match almost any body you decide to use.

So, for those of you that like to do some serious trailing but are worried about splashing grit and grime all up in your chassis, here’s a simple solution. I’ve added a few pix of these mounted on the SCX10 II, however as you can see I’ve left off the floor panels since this particular truck already comes with them.

Product Spotlight: AX31150 Axial Clear Inner Fenders

Product Spotlight: AX31150 Axial Clear Inner Fenders

Product Spotlight: AX31150 Axial Clear Inner Fenders

Product Spotlight: AX31150 Axial Clear Inner Fenders

AX31150 Axial SCX10 Wheel Wells – .040″ (Clear)

Casey Curries AXIALFEST2017 Altra Ultra-Class Axial RR10 Bomber

Casey Curries Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

At #AXIALFEST2016, the Altra Ultra Challenge was one of the most talked-about races at the event. Big time rock junkies came out to race 8 laps around the zig-zaggy campground course – the final mileage total was a whopping 5K! It built quite a bit of interest, so much so that Casey Currie decided to build up another rig for this year’s event!

Casey competed last year and placed 3rd overall, a pretty fantastic feat considering the competition! He did say that it was a bit more strenuous than he expected, but had a fantastic time and would be back.

Here’s a few pix of his horse and a parts list at the bottom. If you’re at AXIALFEST and have a chance, stop by the Axial booth and check out this wicked ride!

Good luck Casey!

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017

Casey Currie's Altra Ultra-Class Axial RR10 Bomber - AXIALFEST2017


Axial Racing

AX90053 RR10 Bomber Kit
AX31433 Axial AR60 Machined Link Mounts
AX31161 Axial Steel Spur Gear 32P 64T
AX30395 Axial Heavy Duty Bevel Gear Set 13/38T
AX31430 Axial King Shock Caps and Collars

Futaba

Futaba S9156 Servo

Vanquish Products Parts

VPS03240 Vanquish Products Wraith Differential Cover
VPS07991 Vanquish Products Yeti/RR10 Motor Mount
VPS07990 Vanquish Products Yeti/RR10 Motor Cam
VPS07970 Vanquish Products AR60 Axle Servo Mount
VPS02410 Vanquish Products Clamping 25T Servo Horn
VPS02004 Vanquish Products Wraith/XR10 C-Hubs
IRC00060 Vanquish Products Incision RR10 Bomber 1/4 Stainless Steel Link Kit
VPS07350 Vanquish Products Yeti Trailing Arms
VPS03200 Vanquish Products Wraith Steering Knuckles
VPS07670 Vanquish Products Wraith/Yeti Clamping Lockouts
VPS06762 Vanquish Products Rigid Industries 1″ LED Light Bar
VPS08030 Vanquish Products KMC 2.2 XD127 Bully Wheels
VPS08300 Vanquish Products Currie Antirock Yeti Sway Bar V2

Tekin Racing

Tekin RX4 Waterproof Hard Box Bluetooth 3.0
Tekin ROC412 Element-Proof HD 2300kV Brushless Motor

Axial MAX-D SMT10 Monster Truck Full Option Build

tech_maxdoption

Words and photos by Tony Phalen

I’ve been looking forward to getting one of Axial Racing’s SMT10 Monster Trucks, so when the MAX-D landed on my doorstep (thanks UPS guy), it was literally a matter of seconds before the box was open and the truck was out. I was even more stoked, however, when I found a big ol’ box of Axial’s aftermarket goodies included so I could do an upgrade article.

Below is a step-by-step guide, walking you through the disassembly and re-assembly of the SMT10 with all of these parts.

STEP 1

Axial MAX-D SMT10 Monster Truck Full Option Build Here’s a overview shot of all the parts I’ll be installing on the MAX-D. A list is included at the end of the article complete with part numbers and links.

STEP 2

Axial MAX-D SMT10 Monster Truck Full Option Build
I’ll be splitting the build up into three sections; front, rear and mid. Here’s a pic of the parts I’ll be using for the front end rebuild; steering parts, upper and lower link plates, link mounts, shock parts, gears and the diff cover.

STEP 3

Axial MAX-D SMT10 Monster Truck Full Option Build
Since the SMT10 is modular in design, I need to remove anything that will keep the front from coming off easily – that being the front tires and servo. Once the servo has been disconnected, you can let it dangle down and under the center transmission.

STEP 4

Axial MAX-D SMT10 Monster Truck Full Option Build
To remove the front ‘clip’, simply unscrew at the three attachment points designated by the red arrows. Do this on both sides and the front end will drop right off. Pay close attention to the WB8 center driveshaft coupler; it fits between the front and center driveshaft sections and, once the front clip is removed, this piece can fall out.

STEP 5

Axial MAX-D SMT10 Monster Truck Full Option Build
Attach the AX31244 Axial Upper Link Plate Set and AX31245 Axial Lower Link Plate Set. Because of the design, I didn’t need to remove anything other than the shocks; that’s fine because I need to work on those at a later time anyway.

STEP 6

Axial MAX-D SMT10 Monster Truck Full Option Build
The AX31432 Axial AR60 Machined Servo Plate and Mount Set is up next for install, but before you do that, assemble it and attach the servo to it. This ensures the two side upright pieces line up with the servo. I would also suggest using a dab of blue threadlocker on the two screws going up and into the aluminum side uprights. Once everything is aligned, remove the servo.

STEP 7

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the stock plastic servo mount and replace with the aluminum assembly from STEP 6.

STEP 8

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the lower links and replace the plastic link mounts with the AX31433 Axial AR60 Machined Link Mounts. Re-attach the lower links.

STEP 9

Axial MAX-D SMT10 Monster Truck Full Option Build
Before moving on, I suggest paying close attention to the orientation of the steering blocks in relation to the lower link mounts. The upgrade C-hubs I’ll be using have more adjustability than the stock plastic ones, so if you just throw them on and clock the C-hub like the original (red arrow), your caster will be WAY off. So, my suggestion is not to assemble to match the C-hub (red arrow), but to assemble to match the top kingpin screw (orange line).

STEP 10

Axial MAX-D SMT10 Monster Truck Full Option Build
But first, remove the steering system. Four screws will do it.

STEP 11

Axial MAX-D SMT10 Monster Truck Full Option Build
I’m also going to replace the diff gears while I’m at this point. Remove the four screws holding on the diff cover and the four screws holding the diff in place. You’ll need to pull the axles out a bit to disengage them from the diff.

STEP 12

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the four screws to release the stock diff gear and replace with the AX30395 Axial Heavy Duty Diff Gear. Make sure the gasket is in place and not still attached to the original diff gear. A keen eye will notice the planetary diff design instead of a locked unit. This type of differential is actually a better fit for Monster Trucks.

STEP 13

Axial MAX-D SMT10 Monster Truck Full Option Build
You’ll need to replace the stock input gear as well; that can be done on the opposite side of the axle. Replace with the AX30395 Axial Heavy Duty Input Gear, re-install the differential and slide the axles back into the housing. You may need to rotate the axles to key them into the differenial.

STEP 14

Axial MAX-D SMT10 Monster Truck Full Option Build
Replace the stock plastic cover with this beautiful AX31429 Axial AR60 Machined High Clearance Differential Cover.

STEP 15

Axial MAX-D SMT10 Monster Truck Full Option Build
Ok, now it’s time for the steering. On one side at a time, pull the plastic parts off, keeping the bearings and hat bushings handy. Re-assemble the the AX30762 Axial XR10 Aluminum C-Hub Carrier and AX31434 Axial AR60 Machined Steering Knuckles. Note the orientation of the parts; if you get confused, look at the opposite side of the steering to make sure you’ve assembled it correctly (the reason why I suggest removing only one side at a time).

STEP 16

Axial MAX-D SMT10 Monster Truck Full Option Build
The AX31428 Axial AR60 Steering Upgrade Kit comes with a small build sheet in it. Use that to assemble the steering links, then attach them to your steering knuckles. The final assembly should look like this.

STEP 17

Axial MAX-D SMT10 Monster Truck Full Option Build
Using STEP 9 as a guide, slide one C-hub onto the axle and secure. Now slide the other C-hub onto the axle and secure.

STEP 18

Axial MAX-D SMT10 Monster Truck Full Option Build
At first, I thought the shocks were going to be a pain; replacing oil, bleeding, etc. However, if you complete this step carefully, you won’t have to do any of that!

Start by inserting the rubber o-ring into the AX31430 Axial King Shocks Aluminum Collars; set aside. Grab your shocks and remove the lower spring retainer and spring. Carefully remove the shock cap and set the shock off to the side in some sort of stand. Pull the bladder out of the shock cap (if it’s up in there) and install it into the AX31430 Axial King Shocks Aluminum Cap; set aside. Grab your shock again and spin the plastic collar off; it can only be removed from the top. Spin the King Aluminum Collar on followed by the King Aluminum Shock Cap. Install the spring from the bottom and the AX31431 Axial Aluminum Shock Spring Retainer. These retainers utilize a small screw to keep them from popping off in the event of an crash. These are, after all, Monster Trucks – there will be plenty of crashing.

STEP 19

Axial MAX-D SMT10 Monster Truck Full Option Build
Re-attach the shocks to the lower links and, wah-lah. Your completed from clip should look like this! Ain’t she pretty?

STEP 20

Axial MAX-D SMT10 Monster Truck Full Option Build
Attach your front end to the chassis; if you’re unsure, use STEP 4 and the three red arrows to remind you. This is also the time to re-attach the servo and servo horn. Use a dab of blue threadlocker on the four screws that attach the servo to the aluminum mounts to make sure they stay put.

STEP 21

Axial MAX-D SMT10 Monster Truck Full Option Build
I’ll be moving to the rear of the MAX-D, installing the parts shown here. The procedure will be pretty much the same as the front end; the only minor difference will be the lockouts. Be sure to pay attention to the WB8 center driveshaft coupler as well.

STEP 22

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the rear clip; STEP 4 and the red arrows will help you out here. You’ll need to remove the anti-roll bar connections that attach at the lower link mount.

STEP 23

Axial MAX-D SMT10 Monster Truck Full Option Build
Attach the AX31244 Axial Upper Link Plate Set and AX31245 Axial Lower Link Plate Set as well as the AX31433 Axial AR60 Machined Link Mounts.

STEP 24

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the lockouts and pull the axles out slightly; this will allow you to remove the rear differential.

STEP 25

Axial MAX-D SMT10 Monster Truck Full Option Build
With the same procedure as the front, replace the stock gear with the AX30395 Axial Heavy Duty Diff Gear.

STEP 26

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove and replace the AX30395 Axial Heavy Duty Input Gear from the other side of the axle, then re-install the diff gear. Cap the opening off with the AX31429 Axial AR60 Machined High Clearance Differential Cover. Key the rear axles into the diff gear, then slide the AX30789 Axial AR60 OCP Aluminum Straight Axle Hub Carriers into place. These are an easy install; they are a straight fit and can’t be clocked like the front C-hub.

STEP 27

Axial MAX-D SMT10 Monster Truck Full Option Build
I replaced the plastic bits with the aluminum upgrades like I did with the front shocks.

STEP 28

Axial MAX-D SMT10 Monster Truck Full Option Build
Boom – the rear clip is done! Your final assembly should look like this.

STEP 29

Axial MAX-D SMT10 Monster Truck Full Option Build
Re-attach the rear clip and connect the anti-roll bar. Since we replaced the plastic link mounts with aluminum, you’ll want to add a small drop of blue threadlocker to help keep the anti-roll bar links in place.

STEP 30

Axial MAX-D SMT10 Monster Truck Full Option Build
Alright – on to my favorite portion of the build, the electronics! Now, this is MAX-D – MAXIMUM DESTRUCTION – so I’m going big and replacing the stock brushed system with some serious Axial mojo; something Tom Meents would be proud of. I’ll be dropping in an AX24260 Axial AE-3 Vanguard Brushless ESC and AX31047 Axial Brushless 3150kV Motor. Since this is a pretty healthy upgrade, I see it only fitting to upgrade a couple other parts as well.

STEP 31

Axial MAX-D SMT10 Monster Truck Full Option Build
To make this part of the build easier, I started by removing the top part of the roll cage and interior.

STEP 32

Axial MAX-D SMT10 Monster Truck Full Option Build
Here’s a better look at the ESC tray. We’ll get to it in a minute.

STEP 33

Axial MAX-D SMT10 Monster Truck Full Option Build
Flip the MAX-D over and remove the four screws that hold the transmission in place. Axial uses two different screw lengths here so to make sure I get them back in the correct holes, I’ve added a little L (for Longer). Once the screws are out, unplug the motor and pull the whole transmission assembly out. It’s actually alot easier than it looks.

STEP 34

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the gear cover followed by the motor and slipper assembly.

STEP 35

Axial MAX-D SMT10 Monster Truck Full Option Build
Remove the stock motor place and replace with the AX30860 Axial Machined Motor Plate.

STEP 36

Axial MAX-D SMT10 Monster Truck Full Option Build
Before attaching the spur gear, make sure you attach the AX31068 Axial Slipper Pads. They’re sticky-backed so they’re not reusable; we have to add new ones to our AX31163 Axial Steel Spur Gear 32P 56T. Re-assemble the slipper clutch. I would suggest tightening down the slipper nut quite a bit; the added power needs a tighter slipper.

The only drawback with the AX31047 Axial Brushless 3150kV Motor is the fact that it uses a 5mm output shaft; the stock motor uses a 3mm. This means you’ll need a new pinion gear. I didn’t want the MAX-D to just have more power, I wanted it to be fast as well, so I’m starting with a AX30839 13T 32P Pinion Gear. MO’ POWA ARH ARH ARH

STEP 37

Axial MAX-D SMT10 Monster Truck Full Option Build
Now that I have a new heart for the MAX-D, it’s time to transplant it back in the truck. Remember to install the screws in the correct holes.

STEP 38

Axial MAX-D SMT10 Monster Truck Full Option Build
Flip the SMT10 back over and remove the top to the receiver box. Carefully pull the stock ESC power lead out of the receiver and remove it from the truck.

STEP 39

Axial MAX-D SMT10 Monster Truck Full Option Build
Apply some double-sided tape to the bottom of the AX24260 Axial AE-3 Vanguard Brushless ESC and attach it to the ESC platform. Route the ESC power lead through the waterproof seal and into the receiver box as shown. Re-attach the receiver box lid.

Finally, plug the brushless motor wires into the ESC, matching the A-wire to the A-plug, the B-wire to the B-plug and the C-wire to the C-plug.

STEP 40

Axial MAX-D SMT10 Monster Truck Full Option Build
The final step is to re-attach both the interior and top of the roll cage. Looks super tough just sitting there! Time to go see what she can do!

Here’s the list of parts used in this article.

Front End
AX30395 Axial Heavy Duty Bevel Gear Set – 38T/13T
AX30762 Axial XR10 Aluminum C-Hub Carrier
AX31244 Axial Upper Link Plate Set
AX31245 Axial Lower Link Plate Set
AX31428 Axial AR60 Steering Upgrade Kit
AX31429 Axial AR60 Machined High Clearance Differential Cover
AX31430 Axial King Shocks Aluminum Caps and Collar Set – 12mm
AX31431 Axial Aluminum Shock Spring Retainer – 12mm
AX31432 Axial AR60 Machined Servo Plate and Mount Set
AX31433 Axial AR60 Machined Link Mounts
AX31434 Axial AR60 Machined Steering Knuckles

Mid-Section
AX24260 Axial AE-3 Vanguard Brushless ESC
AX30839 13T 32P Pinion Gear
AX30860 Axial Machined Motor Plate
AX31047 Axial Brushless 3150kV Motor
AX31068 Axial Slipper Pads
AX31163 Axial Steel Spur Gear 32P 56T

Rear End
AX30395 Axial Heavy Duty Bevel Gear Set – 38T/13T
AX30789 Axial AR60 OCP Aluminum Straight Axle Hub Carrier
AX31244 Axial Upper Link Plate Set
AX31245 Axial Lower Link Plate Set
AX31429 Axial AR60 Machined High Clearance Differential Cover
AX31430 Axial King Shocks Aluminum Caps and Collar Set – 12mm
AX31431 Axial Aluminum Shock Spring Retainer – 12mm
AX31433 Axial AR60 Machined Link Mounts

Installing a Snow Plow on Your SCX10

tech_snowplow

Words and photos by Tony Phalen

Being a SoCal native, I’ve never had a reason to build a RC vehicle with a snow plow attachment. After a move to Connecticut back in 2013, it occurred to me why a slew of snow-moving builds pop up in that latter months of the year. Funny thing is I never took advantage of this situation, that is, until I moved BACK to sunny Southern California in 2015. After seeing a bunch of videos on YouTube with guys plowing their front yards, a friend (in CT) hit me up wanting me to build a custom rig for her husband for his birthday.

The entire build was pretty awesome, but for this article I’m going to just run through the quick steps of attaching RC4WD’s plow unit on the SCX10 Ram Power Wagon.

Step 1

Installing a RC4WD Snow Plow on Your SCX10
My first step in any build is to lay out the parts so I know what I’m working with. We have our SCX10 and the parts from RC4WD’s Snow Plow unit – a pretty simple plow that comes almost completely assembled. A few extra pieces come with the kit to attach it to the frame rails on the SCX10. You’ll also need a spare servo, preferably one with a decent amount of torque.

Step 2

Installing a RC4WD Snow Plow on Your SCX10 The plow attaches to the SCX10 between the frame rails. To get to this area, we need to first remove the stock plastic cap. Two screws is all it takes, then give the plastic cap a good pull to remove it.

Step 3

Installing a RC4WD Snow Plow on Your SCX10 Assemble the bumper mount as shown. You’ll want to make sure the two mounting ‘tabs’ (red arrow) are tilted up; this angles the plow correctly once installed. Also take note of the flat area on the plow mounts (green arrow) – notice the flat spot is pointing down. I suggest using blue threadlocker on all the screws here to prevent them from falling out.

Step 4

Installing a RC4WD Snow Plow on Your SCX10 Time to install the servo, however before you do, I suggest removing all of the screws (one at a time) and re-installing with a dab of blue threadlocker. I also advise removing the plow blade entirely during the install.

Moving on – slide the servo into place and attach (don’t forget your blue threadlocker). Attach one end of the chain to the servo horn and the other end to the bottom plow pickup. Typically, servos come with the output shaft set at 90°, so let’s start by attaching the servo horn angled up a bit like the photo. We can adjust the ‘pull height’ after we have the entire unit installed. You can re-install the plow blade at this point.

Step 5

Installing a RC4WD Snow Plow on Your SCX10Attach the bumper mount assembly (from Step 3) to the plow assembly. The mount slides into ‘keyed’ slots in the back of the plow assembly. Blue threadlocker is suggested here.

Step 6

Installing a RC4WD Snow Plow on Your SCX10Slide the mounting tabs between the frame rails and secure with the button head screws. Again, blue threadlocker is suggested here as well.

Step 7

Installing a RC4WD Snow Plow on Your SCX10
Remove the receiver box top and feed the servo lead into the box. Axial uses a 3-channel Tactic radio system, so thankfully there is an open port for the plug – port 3. Re-install the receiver box top.

Now, before you head on out to remove some snow, we need to test the plow for proper operation. Turn the transmitter on, then plug in the battery and turn the SCX10 on. There are two buttons right under your thumb (on the transmitter) – one raises the plow, the other lowers it. Go ahead and give it a quick test. If the buttons raise and lower the plow, you’re good to go. If you want the plow to raise up more, you have 2 options; 1) remove the servo horn and angle it up more or 2), shorten the chain by changing the attachment points.

Good luck and happy plowing!

axial-article-cover-photo-1

Here is a list of parts used in this article:

AX90037 SCX10™ Ram Power Wagon 1/10th Scale Electric 4WD – RTR
Z-X0007 RC4WD Blade Snow Plow
36645 Hitec D‑645MW 32‑bit, High Speed, Metal Gear Servo

Yeti SCORE Trophy Truck Full Option Build

tech_yetitrophytruckfulloption

Words and photos by Tony Phalen

Whenever I get a new vehicle, I like to take the first couple weeks to just drive it in box-stock form to learn about its traits; how it handles, any quirky nuances, etc. During this time I also take some time to review any hop ups that might become available, giving me an idea on how my long-term upgrade process is going to play out. Thankfully, the SCORE Trophy Truck shares the same platform as the Yeti Rock Racer, which means that there are a slew of performance goodies already available. Armed with a bag of aluminum bits, I decided it was time to install them prior to getting this rig all dirty. Not only did that make it a lot easier to deal with (read: no dirt!), it also looks much prettier in pictures. Time for an Axial Yeti SCORE Trophy Truck Full Option Build!

Step 1

Axial Yeti SCORE Trophy Truck Full Option Build Here are the parts I’ll be installing in this article. I’ve got quite a bit of work ahead; shocks, gears, machined parts and turnbuckles. A full list of the parts I installed is included at the bottom of this article.

Step 2

Axial Yeti SCORE Trophy Truck Full Option Build Since I’m going to need to remove the center transmission for upgrades, I disconnected the motor wires from the ESC. Pay attention to how the wires connect; if you have a photographic memory, you’re good to go. If not (like me), you can mark them to keep things straight. I put one silver mark for the A wire, 2 for the B and 3 for the C.

Step 3

Axial Yeti SCORE Trophy Truck Full Option Build I’m going to be working on the front end of the SCORE TT first. I started by removing the top deck support brace. It requires the removal of 10 screws in two different lengths so, to keep things organized, I put them back in the holes after removal.

Step 4

Axial Yeti SCORE Trophy Truck Full Option Build Once the top deck support brace has been lifted off, removal of the front clip is easy. There are 4 screws underneath the chassis and the two hinge pin screws. I also disconnected the fixed-length steering turnbuckles as well – I’m replacing them with adjustable ones.

Step 5

Axial Yeti SCORE Trophy Truck Full Option Build Separate the gearbox from the shock tower by removing the 4 screws holding them together. I’m only working with the differential at this time so I set the rest of the front clip assembly aside. Note the orientation of the diff in the gearbox. You’ll want to make sure you re-install it the same way.

Step 6

Axial Yeti SCORE Trophy Truck Full Option Build Next, I removed the differential and bevel gear assemblies from the gearbox. I’m replacing them with the AX30395 Heavy Duty Bevel Gear Set shown in the picture. One thing to notice is that the assemblies have straight cut gears; this design is pretty strong and easy to machine. The new HD versions are helical cut, or machined with a slight angle in them. These are great for high-torque applications like crawlers or, in this case, hardcore trophy trucks! To replace, remove the 4 screws on the diff to release the gear, set the new gear in place and re-install the 4 screws. If you’re the tinkering type, you might think about adding some optional fluid to the diff prior to putting it back together (I did, 1000wt). The HD bevel gear is a one-piece unit so replacing the stock part is a simple pull-and-replace operation. One final step I performed was to remove the rubber stops that are installed in each diff outdrive. If you hold the diff on its side, you’ll see them down inside there. These are used to keep the dogbones tight and prevent them from ejecting during a hard crash, however they hinder the up and down suspension movement slightly. Since I’ll be replacing the dogbones with universals, they’re not needed anymore.

Step 7

Axial Yeti SCORE Trophy Truck Full Option Build Next up was the AX31170 Machined Front Shock Tower and AX31169 Machined Body Post Mount. These parts are a direct bolt on and work the same as the stock parts, however as you can see there are a few extra pieces. I’ll get to those in a bit.

Step 8

Axial Yeti SCORE Trophy Truck Full Option Build I disassembled the front clip down to the front shock tower assembly. The only part I’ll be reusing from this is the plastic body post.

Step 9

Axial Yeti SCORE Trophy Truck Full Option Build I attached the AX31169 Machined Body Post Mount to the AX31170 Machined Front Shock Tower. Since this is an aluminum-to-aluminum connection, I used a dab of threadlocker on the screws to make sure they don’t loosen up. I slid the plastic body post into the mount and used the screws provided to secure.

Step 10

Axial Yeti SCORE Trophy Truck Full Option Build I’m ditching the stock dogbone setup for a set of Axial’s AX31135 94mm Universal Axle Set. These come as a pair, are pre-assembled and slide right into place.

Step 11

Axial Yeti SCORE Trophy Truck Full Option Build I re-assembled the front clip – the new shock tower to the gearbox and the front bumper to the tower. I left the shocks off for now since I was replacing them with a full set of Axial’s Icons. You can also see the aluminum upper shock mounts that are included with the aluminum shock tower.

Step 12

Axial Yeti SCORE Trophy Truck Full Option Build For strength and additional tuning, I’m adding a full set of front adjustable turnbuckles (AX31249 Yeti Turnbuckle Set). This kit includes an excellent build sheet, so assembly is very easy. Just build the turnbuckles to the appropriate lengths and you’re good to go. I would suggest keeping them separate during the build so you don’t mix up the steering links with the camber links; the two are different.

Step 13

Axial Yeti SCORE Trophy Truck Full Option Build Before attaching the front clip back on the TT, I need to do a little work on the transmission. I pulled it from the TT and removed the gear cover, motor, plastic backing plate and plastic motor mount.

Step 14

Axial Yeti SCORE Trophy Truck Full Option Build I installed Axial’s AX31156 Machined Adjustable Motor Mount, a 2-piece unit that includes the main mount that attaches to the gearbox and a mount that attaches to the motor. The motor mount part swivels to adjust the gear mesh and uses an upper clamp to keep it securely in place. Because it’s aluminum, this system is SUPER strong and helps pull unwanted heat away from the motor. I re-attached the plastic backing plate followed by the spur gear assembly (I used Axial’s AX31161 32P 64T Steel Spur Gear and AX31164 Machined Slipper Plates in place of the stock parts). These upgrades look awesome and should make the gearbox virtually bulletproof. After I tightened everything up, I went ahead and re-installed the gearbox into the TT.

Step 15

Axial Yeti SCORE Trophy Truck Full Option Build Time to get the front back together, so I started by sliding the front clip onto the chassis and securing with the 4 screws from underneath as well as the two hinge pins. I made sure to key the center universal into the outdrive located under the transmission. It’s a little tricky, so I would suggest rotating the transmission gears (using the back tires) until you see the slots in the outdrive; this will make it easier to key the universal. Next, I slid the front axles through the steering blocks, attaching the wheel hexes to keep them in place. I installed the steering and camber links, making sure to key the axle bones into the outdrives. A little care has to be taken here to make sure the axle bones stay inside the outdrive.

Step 16

Axial Yeti SCORE Trophy Truck Full Option Build Now that the front is back on and looking good, it was time to move on to the rear clip and the installation of a lot of performance parts. The first thing I needed to do is separate the rear clip from the rest of the chassis; front cage screws, rear cage screws and the 4-link mounts. If you did it right, this is what you should be left with.

Step 17

Axial Yeti SCORE Trophy Truck Full Option Build My first plan of attack is the rear differential. To extract it, I needed to remove the diff cover, the straight axle hub carriers and the axles (just pull them out slightly). I also removed the two plastic diff-capture plates that hold the diff in place. Note the orientation of the diff gear inside the housing.

Step 18

Axial Yeti SCORE Trophy Truck Full Option Build Replacement of the diff gear and bevel gear is the same as the front. Once completed, re-assemble by inserting the diff gear, diff-capture plates and axles (key and slide back into place). I installed the optional AX30789 AR60 OCP Aluminum Straight Axle Hub Carrier.

Step 19

Axial Yeti SCORE Trophy Truck Full Option Build To strengthen the rear end, I replaced the stock plastic 4-link mount with the AX31165 Machined 4-Link Mounts as well as added Axial’s AX31244 Upper Link Plate Set. Both are direct bolt ons; the Upper Link Plate Set uses existing holes in the plastic links.

Step 20

Axial Yeti SCORE Trophy Truck Full Option Build I also installed Axial’s AX31245 Lower Link Plate Set. These also bolt right on using existing holes in the plastic links. I would suggest installing and tightening the two end screws while leaving the centermost pair loose. They can be tightened up when you re-install the shocks and anti-roll bar.

Step 21

Axial Yeti SCORE Trophy Truck Full Option Build Here is the rear clip assembled with all of the aluminum parts installed. You can see I’ve also added the AX31166 Machined Shock Mount Plates, AX30830 AR60 OCP Machined Link Mounts and AX31167 Machined Sway Bar Clamps. The Machined Sway Bar Clamps are a little hard to see, but I’ve added some additional pictures at the end that help show their install. When re-attaching the rear clip back to the chassis, add some threadlocker to the screws that secure the aluminum 4-link mounts. This will help prevent the screws from backing out when you’re out having a good time.

Step 22

Axial Yeti SCORE Trophy Truck Full Option Build While I loved the look of the King shocks, I couldn’t pass up installing a full set of Axial’s Icons. Per the included instructions, I built a set of front and rears and installed them in place of the Kings. I have an additional set of shocks to create a dual-shock setup, but I’m going to give it a whirl with the single shocks first. The dual-shock install (and tuning) will be for a later article. As you can see from the pictures, the aluminum parts look awesome and will provide additional strength as well as give the truck a bit more of a ‘factory’ look. Time for me to get outside and get this thing dirty!

Here’s the list of parts used in this article.

AX30395 Heavy Duty Bevel Gear Set – 38T/13T (x2)

AX30789 AR60 OCP Aluminum Straight Axle Hub Carrier

AX30829 AR60 OCP Machined Low-Profile Differential Cover

AX30830 AR60 OCP Machined Link Mount

AX31135 Universal Axle Set 94mm

AX30836 Aluminum Servo Horn 25T

AX31136 Icon 87-125mm Aluminum Shock Set

AX31156 Machined Adjustable Motor Mount

AX31161 Steel Spur Gear 32P 64T

AX31164 Machined Slipper Plate

AX31165 Machined 4 Link Mounts

AX31166 Machined Shock Mount Plates

AX31167 Machined Sway Bar Clamp

AX31169 Machined Body Post Mount

AX31170 Machined Front Shock Tower

AX31172 Icon 67-90mm Aluminum Shock Set

AX31244 Upper Link Plate Set

AX31245 Lower Link Plate Set

AX31249 Yeti Turnbuckle Set

Additional Photos Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build Axial Yeti SCORE Trophy Truck Full Option Build IMG_0552 IMG_0557 IMG_0555 IMG_0556